User manual PIONEER DEH-1320MP

[. . . ] This operation manual will help you benefit fully from this units potential and to maximize your listening enjoyment. We recommend that you familiarize yourself with the functions and their operation by reading through the manual before you begin using this unit. It is especially important that you read and observe precautions noted on this page and in other sections. !Always keep the volume low enough so that you can hear sounds from outside the car. [. . . ] 2 Press c/d/a/b to select a listening position. Button c d a b Display Front Left Front Right Front Seat All Seat Position Front seat left Front seat right Front seats All seats English # To cancel the selected listening position, press the same button again. # You cannot select All Seat when NW mode has been selected. Using balance adjustment You can select a balance setting that provides an ideal listening environment in all occupied seats. Each press of c or d moves the left/right speaker balance towards the left or the right. BAL: L25 BAL: R25 is displayed as the left/ right speaker balance moves from left to right. Using the position selector One way to assure a more natural sound is to clearly position the stereo image, putting you right in the center of the sound field. The position selector function lets you automatically adjust the speakers output levels and inserts a delay time to match the number and position of occupied seats. En 39 Section 08 Audio Adjustments Using balance adjustment You can select a fader/balance setting that provides an ideal listening environment in all occupied seats. Each press of a or b moves the front/rear speaker balance towards the front or the rear. FAD: F25 FAD: R25 is displayed as the front/ rear speaker balance moves from front to rear. !Custom is an adjusted time alignment that you can create for yourself. (Refer to Auto TA and EQ (auto-time alignment and auto-equalizing) on page 49. ) # You cannot select Auto TA when NW mode has been selected. This indicates that you cannot select Auto TA if auto TA and EQ has not been carried out. # FAD:FR00 is the proper setting when only two speakers are used. Adjusting the time alignment You can adjust the distance between each speaker and the selected position. Press AUDIO until TA. 2 appears in the display. 3 Press c or d to adjust left/right speaker balance. Level The difference in reproduced levels between speaker units can be corrected. Slope Adjusting the HPF/LPF slope (filter attenuation slope) lets you adjust the continuity of sound between speaker units. The slope indicates the number of decibels (dB) the signal is attenuated when the frequency is one octave higher (lower) (Unit: 42 En Section Audio Adjustments 08 !(Pass), the audio signal bypasses the filter, so the filter does not have an effect. Phase adjustment When the cross-over point value for filters on both sides is set to 12 dB/oct. , the phase is reversed 180 degrees at the filter cut-off frequency. In this case, reversing the phase assures improved sound continuity. Normal phase Reverse phase # To cancel the muting, press a. 3 Press and hold b to mute the selected speaker unit (filter). MUTE blinks in the display. English Adjusting network 1 Press AUDIO and hold until second audio menu appears in the display, then press AUDIO to select NW. 1. After second audio menu is displayed, press AUDIO until NW. 1 appears in the display. Each press of c or d selects the speaker unit (filter) in the following order: Low LPF (low-range speaker LPF)Mid HPF (middle-range speaker HPF)Mid LPF (middle-range speaker LPF)High HPF (highrange speaker HPF) 3 Press AUDIO to select NW. 2. 4 Press c or d to select the cut-off frequency (crossover frequency) of the selected speaker unit (filter). Each press of c or d selects cut-off frequencies (crossover frequencies) in the following order: Low LPF: 31. 540506380100125 160200 (Hz) Mid HPF: 31. 540506380100125 160200 (Hz) Mid LPF: 1. 622. 53. 15456. 38 1012. 516 (kHz) High HPF: 1. 622. 53. 15456. 38 1012. 516 (kHz) 5 Press a or b to adjust the level of the selected speaker unit (filter). [. . . ] 14. 4 V DC (allowable voltage range: 12. 0 14. 4 V DC) Grounding system . . . . . . . . . . . . . . . . . . . current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 7 kg Continuous power output is 22 W per channel minimum into 4 ohms, both channels driven 50 to 15, 000 Hz with no more than 5% THD. 4 W (4 8 W allowable) Preout max output level/output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]