User manual PIONEER DDJ-WEGO2

[. . . ] DJ Controller DDJ-WEGO2 http://pioneerdj. com/support/ The Pioneer DJ support site shown above offers FAQs, information on software and various other types of information and services to allow you to use your product in greater comfort. Operating Instructions Contents How to read this manual ! Thank you for buying this Pioneer product. Be sure to read both this leaflet and Read Before Use (Important)/ Quick Start Guide!Both documents include important information that you must understand before using this product. ! In this manual, names of screens and menus displayed on the computer screen, as well as names of buttons and terminals on the product, etc. , are indicated within brackets. [. . . ] This problem can arise when the mobile phone’s communications protocol is GSM, and is due to interference caused by GSM. If this happens, change the iPhone/iPad’s setting to flight mode. This problem does not occur with the 3G or LTE communications protocols. 1 Operate the channel faders to adjust the audio level output from the respective decks. 2 Operate the crossfader to switch the deck whose sound is output from the speakers. — Left edge: Sound is output from deck [A] or [C]. ! The curve characteristics can be switched using the crossfader curve setting button on the [MIXER] panel at the center of the computer’s screen. — [ — [ — [ ]: Set here for a curve that rises gradually. ]: Sets an abruptly rising curve. 1 Connect the iPhone/iPad with this unit using the iPhone/iPad connection cable (Lightning). 2 Connect this unit with the USB mobile battery or USB power adapter. 4 Launch the DJ application on the iPhone/iPad. 3 Turn the [MASTER VOL] control to adjust the audio level of the speakers. Adjusting the sound quality Turn the [EQ (HI, MID, LOW) ] controls on the respective decks. 12 En Monitoring sound with headphones (rC) 1 Connect headphones to the [PHONES] terminal. ] button for the deck you want to Quitting the system 1 Quit VIRTUAL DJ LE. 3 Disconnect the USB cable from your computer. 3 Turn the [HEADPHONES MIX] control. ! Turn counterclockwise: The volume of the deck whose [CUE ] button is pressed increases relatively. ! Turn clockwise: The [MASTER OUT] volume increases relatively. Basic Operation 4 Turn the [HEADPHONES VOL] control. ! The sound of the deck whose [CUE from the headphones. ! When the [CUE ] button is pressed is output ] button is pressed again, monitoring is canceled. Mixing (rB, D) 1 Operate the [TEMPO] slider to match the playing speed on one deck to the playing speed on the other deck. — Move towards the + (front) side: The playing speed increases. — Move towards the – (back) side: The playing speed decreases. 2 If the beats of the two decks are off, use the jog dial’s pitch bend function to correct for this offset. The playing speed can be adjusted by turning the outer part of the jog dial during playback. ! When the [SYNC (MASTER)] button is pressed, the two decks are automatically set to the same playing speed. (The playing speed is set to the speed of the deck selected as the master for synchronization. ) 3 Operate the channel faders or crossfader to mix the sound of the two decks and switch between them. Notes ! If the beats of the two decks do not match, the jog dial of the deck selected as the master for synchronization lights in the set illumination color and the jog dial of the other deck is off. ! Once the beats of the two decks are matched, both jog dials light in the set illumination color. For the illumination color setting, see Changing the color of the jog dial’s illumination (rF) on page 14. Inputting the sound of the microphone The sound of the microphone connected to the [MIC] terminal can be mixed. 1 Connect the microphone to the [MIC] terminal. 2 Adjust the audio level input to the [MIC] terminal. ! Turn the [MIC VOL] control: The [MIC] terminal’s input audio level is adjusted. ! The sound of the microphone is not output from the headphones. En 13 Operation (this unit’s features) E F E ! When the jog dial is turned while multiple modes are on, the parameters of the modes that are on (for effects, parameter 1) are adjusted simultaneously. ! All modes are cancelled by pressing the [CTRL A] or [CTRL B] button while pressing the [SHIFT] button. ! The respective effect’s type can be selected by pressing the [FX1], [FX2] or [FX3] button while pressing the [SHIFT] button. [. . . ] ! Intel, Pentium, and Intel Core are trademarks of Intel Corporation in the U. S. ! iOS is a trademark on which Cisco holds the trademark right in the US and certain other countries. The names of companies and products mentioned herein are the trademarks of their respective owners. This product has not been licensed for commercial purposes (for profit-making use), such as broadcasting (terrestrial, satellite, cable or other types of broadcasting), streaming on the Internet, Intranet (a corporate network) or other types of networks or distributing of electronic information (online digital music distribution service). [. . . ]