User manual PIONEER CT-W710R

[. . . ] To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the D3-4-2-1-7b_A_En equipment on thick carpet or a bed. To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or D3-4-2-1-7c_A_En strong artificial light) Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. [. . . ] 2 Push open the tabs, then insert one wire fully into each terminal, then release the tabs to secure the AM antenna wires. If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. Don't let it come into contact with metal objects and avoid placing near computers, television sets or other electrical appliances. For best results, extend the FM antenna fully and fix to a wall or door frame. Use the RCA/phono jack audio cable to connect this unit's LINE OUT connectors to the analog input connectors of an amplifier. Make sure to complete all connections before connecting to an AC outlet. ⷠConnect the power cord to the AC inlet (AC IN) on the rear panel of the tuner, then plug into a AC outlet. Liquid Crystal Display The LCD used in this unit has a tendency to change color in response to the surrounding temperature. The display's color tone may turn gray or its ability to switch between displayed information may slow down when the room is not at optimum temperature, or when the unit has been operating for a long period of time. However, these are only temporary symptoms and regular functionality will be restored once the unit returns to optimum temperature. 4 RDS indicator Lights when an RDS broadcast is received, and flashes during RDS search. If a station cannot be preset automatically due to poor reception, use the "Manual tuning" operation to tune in the station, then preset it using the manual "Preset stations" operation. 1 Make sure that the unit is in standby mode, and then press the button to turn on the power. When the first broadcast station is found, that station is stored in the preset memory at channel A1. Subsequent stations are automatically stored in order at preset channels A1 to A10, B1 to B10, C1 to C10, D1 to D10, E1 to E10, F1 to F10, G1 to G10, H1 to H10, I1 to I10 and J1 to J10 for a maximum of 100 stations. ⷠChannel A1 is tuned in after the auto preset memory operation is completed. 4 Either turn the TUNING/PRESET dial or press the ST + or ST ­ button to select the search mode. The frequency changes continuously when the TUNE + or TUNE ­ button on the remote control unit is held in. ⷠWhen the MPX mono mode has been selected, FM stereo broadcasts will be received in monaural, and the STEREO indicator will light blue. 4 Either turn the TUNING/PRESET dial or press the ST + or ST ­ button to select the search mode. Automatic searching will begin, and then stop when a station is received. ⷠWhen the unit is in the MPX stereo mode and FM band auto tuning is selected, the front-panel STEREO indicator will light red when a stereo broadcast is received. [. . . ] This function eliminates the need to perform complicated resettings when the power is switch on. This function provides approximately two week of memory storage when the main unit's POWER button is off and with the power cord disconnected. When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initializaton of the microprocessor is required by the following procedure. 2 Press the unit's POWER button to turn the power on while holding down the MENU button. [. . . ]