User manual PIONEER CT-W700R

[. . . ] To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the D3-4-2-1-7b_A_En equipment on thick carpet or a bed. To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or D3-4-2-1-7c_A_En strong artificial light) Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. [. . . ] Be sure to unplug the power cord whenever leaving your home for vacations or when otherwise not using the unit for extended periods of time. ⷠWhen the unit is in the standby mode, if the power is turned off by pressing the main unit's POWER button, the power will not turn on if the button is pressed again. To turn on the power in this case, press either the remote control unit's button or a different button (other than the POWER button) on the main unit. ⷠWhen the unit is in the standby mode, if the power is turned off by unplugging the power cord, the power will not turn merely by reconnecting the power cord. To turn on the power in this case, reconnect the power cord and then press either the remote control unit's button or a different button (other than the POWER button) on the main unit. The unit times out if no operation is performed for about five seconds after the menu mode is set. Turn the dial clockwise to change the reception toward higher frequencies. Turn the dial counterclockwise to tune the reception toward lower frequencies. When inputting station names, use this dial to select desired characters (page 18). Hold the button depressed for two seconds or longer during DAB mode to perform full scan operation (Full band and L-band). Press the button briefly during DAB mode to perform a local scan (UK band III) for UK broadcast services (UK stations are in the range of 11B to 12D). 1 When the preset channel is A1, pressing the ST ­ button or rotating the TUNING/PRESET dial to the left will cause the preset channel to move to J10. Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information, such as the name of the station and the kind of show being broadcast. For example, you can search for a station that's broadcasting a show with the program type, JAZZ. You can search the following program types:1 POP M ­ Pop music ROCK M ­ Rock music EASY M ­ Easy listening LIGHT M ­ `Light' classical music CLASSICS ­ `Serious' classical music OTHER M ­ Music not fitting above categories WEATHER ­ Weather reports FINANCE ­ Stock market reports, commerce, trading, etc. CHILDREN ­ Programs for children SOCIAL ­ Social affairs RELIGION ­ Programs concerning religion PHONE IN ­ Public expressing their views by phone TRAVEL ­ Holiday-type travel information as opposed to traffic announcements. LEISURE ­ Leisure interests and hobbies JAZZ ­ Jazz COUNTRY ­ Country music NATION M ­ Popular music in a language other than English OLDIES ­ Popular music from the '50s and '60s FOLK M ­ Folk music DOCUMENT ­ Documentary You can search for any of the program types listed above. 3 Select "RDS" by either rotating the TUNING/PRESET dial or pressing the ST + or ST ­ button, then press either the TUNING/ PRESET dial or ENTER button. 4 Either turn the TUNING/PRESET dial or press ST + or ST ­ button to select the desired search mode (RDS search, PTY search or TP search). 5 Press the TUNING/PRESET dial or ENTER button to search for the RDS program you want to hear. When it finds one, the search stops and the station plays for five seconds. 6 If you want to continue listening to the station, press the TUNING/PRESET dial or ENTER button within five seconds. [. . . ] Using the unit's TUNING/PRESET dial, select either "Yes" or "No" and press the TUNING/PRESET dial. 4 If "Yes" is selected, the memory will be cleared and the unit will then be set to standby mode. ⷠIf the microprocessor has been reset, all the button settings are reset to the default values (the values set upon shipment from the factory). Make sure the power is switched off before making or changing the connections. [. . . ]