User manual PIONEER CT-W310

[. . . ] 12 - Switching to the Main Menu Balance Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - Using the Position Selector - Fine Tuning the Position - Effective distance Adjustment Using the Position Fine Tuning function Source Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - About the System Reset button - Before system resetting - System Resetting All Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - About the All Clear button - Before all clearing - All clear Protecting System Reset button and All Clear button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select the position when measuring the distance to be corrected as shown on the page 34. Note: · The correct distance can not be input unless these operations are conducted. 4. Press FUNCTION buttons 3 or 5 and select the speaker channel to input. Press the buttons to switch between left (LEFT) and right (RIGHT). 5. Press FUNCTION buttons 1 or 2 and select the band to input. Each press of the FUNCTION buttons 1 or 2 select the desired band in the following order: S. W. (ultrabass-range) Ô LOW (low-range) Ô MID (mid-range) Ô HIGH (highrange) 35 6. Press the 5/ buttons to input the distance to be corrected (delay time). Input the distance to be corrected, as measured on page 34. Holding down these buttons continues their operations (during distance tuning, holding down the button moves the distance 1. 54 cm/1 step). ENGLISH ESPAÑOL 7. Carry out time alignment adjustments for the other speaker units. Repeat steps 4 ­ 6 to input the distance to be corrected for each speaker unit. Note: · Some systems may indicate values for speaker units which are not connected. Verify the composition of the system in order to correctly adjust the bands for the connected speaker units. DEUTSCH FRANÇAIS ITALIANO NEDERLANDS 36 Audio Adjustment <Network> Filter Adjustment <FTR> (Open state) The following adjustments can be made during filter adjustments. Make the appropriate adjustments for the reproduced frequency band and characteristics of the connected speaker unit. Filter frequency adjustment: Every 1/3 octave Level adjustment: 0. 5 dB/1 step The cut-off frequencies of the high pass filter (H. P. F. ) and the low pass filter (L. P. F. ) of each band (subwoofer, low, mid, high) and the reproduction level of each band are set up. Set up the cut-off frequencies of each filter for all the bands. Repeat steps 5 and 6 to adjust each filter so that the band used and crossover frequency are appropriately located. 39 Important points in adjusting cut-off frequencies · If the subwoofer is installed in the rear tray, setting a high cut-off frequency of L. P. F. of the subwoofer separates the bass and gives the listener the feeling that the bass is coming from behind. · Speakers used for mid and high-ranges are generally constructed to handle a limited level of input compared to low range speakers. is set lower than necessary, strong bass signals can reach the speaker and may damage it. ENGLISH Important points in adjusting the level · The low band, because of its sound frequency characteristics, incorporates the basic frequencies of many musical instruments. It is recommended that the level adjustment of the low band be made first, and then the level adjustment of the mid, high, and subwoofer be made in that order. ESPAÑOL 8. Press the 5/ buttons and adjust the level of each band. Holding down these buttons continues their operations. Switch to each band and adjust the level in order to create a better overall balance. DEUTSCH 9. Press FUNCTION button 3 and adjust the slope of each filter. Press the button to change the adjustment values. The slope can be set up for either the high pass filter or the low pass filter. When setting up, have in mind the adjustments to be made to the next band. FRANÇAIS 10. Press FUNCTION button 4 and adjust the phase of each band. Press the button to change between normal (NOR) and reverse (REV). [. . . ] The fuse is blown. 61 65 61 ITALIANO Incorrect connection. 58 ~ 67 Unnatural sound The mode setting switches are incorrectly set. 56 ~ 57 NEDERLANDS 70 Specifications GENERAL Power Source . . . . . . . . . DC 14. 4 V (10. 8 -- 15. 1 V allowable) Grounding system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current consumption (Rated Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 A (No signal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]