User manual PIONEER CT-S630S

[. . . ] 9) Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. [. . . ] You can't use this setting when the HDMI or component video signals are being input. Important · The explanations for ZONE 3 below only apply to the CT-S630S. Each press selects a MULTI-ZONE option: · ZONE 2 ON ­ Selects your primary (ZONE 2) sub zone · ZONE 2&3 ON2 ­ Select both sub zones · ZONE 3 ON2 ­ Selects your secondary (ZONE 3) sub zone · MULTI ZONE OFF ­ Switches the MULTI-ZONE feature off The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON. 2 Press MULTI-ZONE CONTROL on the front panel to select the sub zone(s) you want. If you selected ZONE 2&3 ON above, you can toggle between ZONE 2 and ZONE 3. · When the receiver is on, 3 make sure that any operations for the sub zone are done while ZONE and your selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone only. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 CD-R sends the source connected to the CD-R inputs to the primary (ZONE 2) sub room. · If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets on page 45 if you're unsure how to do this). 4 4 When Speaker System is set to ZONE 2, use the MASTER VOLUME dial to adjust the volume for the sub zone. 5 When you're finished, press MULTI-ZONE CONTROL again to return to the main zone controls. You can also press MULTI-ZONE ON/OFF on the front panel to switch off all output to the sub zone(s). 5 Switching the speaker terminals If you selected Speaker B at Speaker system setting on page 83, you can switch between speakers using the SPEAKERS button. You can use this if you find that the OVER indicator lights often or you can hear distortion in the sound. 2 · Press RECEIVER , then press A. ATT to switch the input attenuator on or off. a. You can only use this button when Speaker System is set to ZONE 2. Using the sleep timer Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). 1 Keep in mind you can't make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 15 for more on connections). Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use the same type of video cable for connecting your recorder as you used to connect your video source (the one you want to record) to this receiver. For example, you must connect your recorder using Component video if your source has also been connected using Component video. The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. · Press RECEIVER , then press SLEEP repeatedly to set the sleep time. 30 min Off 60 min 90 min · You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again. 3 Dimming the display You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds. · Press RECEIVER , then press DIMMER repeatedly to change the brightness of the front panel display. Note 1 · The receiver's volume, Audio parameters (the tone controls, for example), and surround effects have no effect on the recorded signal. · Some digital sources are copy-protected, and can only be recorded in analog. 2 The attenuator isn't available with digital sources, or when using the Stream Direct (ANALOG DIRECT) modes. If any zone is on, the sleep timer continues functioning. 63 En 08 Using other functions Switching the HDMI output (CT-S630S only) Set which terminal to use when outputting video and audio signals from the HDMI output terminals. [. . . ] 350 mV/2. 2 k Signal-to-Noise Ratio (IHF, short circuited, A network, Pure Direct Mode) LINE . 5 Hz to 100 000 Hz dB (Pure Direct Mode) Note · Specifications and the design are subject to possible modifications without notice, due to improvements. Tuner Section Frequency Range (FM). Loop antenna (balanced) Video Section Signal level Composite Video . . Y: 1. 0 Vp-p (75 ), PB, PR: 0. 7 Vp-p (75 ) Corresponding maximum resolution Component Video. [. . . ]