User manual PIONEER CNDV-1100HD

[. . . ] Precaution Precaution Licence agreement Upgrade Instructions and Operation Manual Addendum 2012 HDD NAVIGATION UPGRADE DISC CNDV-1100HD This software upgrade will result in changes to certain features and availability of information. While the changes are intended to improve the overall user experience for most users, Pioneer and its licensors disclaim any warranty or liability for damages in connection with such changes. !Read the entire manual before upgrading the programme of your navigation system. The actual screens may be changed without notice for performance and function improvements. Models to be upgraded This package can upgrade the software programme and database of the following models: AVIC-HD1BT, AVIC-HD3, AVIC-HD3 II ! [. . . ] NEVER stop the engine of your vehicle nor turn off the power supply to the navigation system until the installation is completed. Turning the power off in this phase causes a malfunction or failure of the navigation system. 3 Press the OPEN CLOSE button and insert the upgrade disc into the disc loading slot. 5 Touch [Yes]. After you touch [Yes] in this screen, you cannot abort the update until the installation of the system programme finishes. The update takes approximately 3 hours in total. 9 Check the details of the caution message and touch [OK]. You can operate the navigation system by touching keys displayed on the screen as usual. 11 Press the OPEN CLOSE button and press the EJECT button to eject the upgrade disc. If you upgrade your navigation system by these discs, the system will have the following changes. Phase 1: Update the database Upgrade procedures 1 Park your vehicle in a safe place. You can perform simplified operations by using the TRK (c/d) button and VOL (b/a) button. (We recommend changing the AV source to “AM” or “FM” before you start the update. ) !If you turn the ignition switch off (the navigation system turns off) or eject the upgrade disc, the update resumes when the navigation system turns on or the disc is reinserted. 2 Press the MAP button to display the current location. CAUTION For users who use AVIC-HD3 II or use the hardware upgraded by CNDV-800HD, updating another software programme will begin first. While this screen is visible, NEVER switch the ignition key position or turn off the power of navigation system. Renewal data The following data are updated: !Touch to toggle the selection. After the installation is complete, the navigation system restarts. p The users who use other models can skip this caution and proceed to the next step. The message “Password obtained from Pioneer should be entered to update. Alternative options: No: Shows the device number (Device#) of your navigation system. 6 Enter the password for authentication that you obtained, then touch [OK]. When the installation of “Disc 1” is finished, the message that “Disc 2” is required appears. When the update of map database is completed, the finished message appears. 8 Touch [OK] to restart the system. Checking whether the upgrade was done properly Display “Service Information” screen to compare the current version number with the previous one. = For details of the operation, refer to Checking the device number. POI data coverage Approximately 5. 7 million POIs are included in the database. p For the modified categories that can be used on “Overlay POI”, “Vicinity Search” and used on the voice recognition, refer to Category list for vicinity search (Renewal). p Some POI information may not be accurate or may become inaccurate through the passage of time. Please directly contact the POI to verify the accuracy of the information about the POI which appears in this database. POI information is subject to change without notice. Time restrictions This is a new feature. This setting controls whether streets or bridges have traffic restrictions during a certain time should be taken into account. [. . . ] p Settings marked with an asterisk (*) show that these are default or factory settings. 1 Name Enter the name to be displayed in the phone book. If you enter the name for new entry, you can select whether you use this entry as voice commands. 2 Pronunciation You can enter the desired pronunciation independently from the name. p If “Pronunciation” is blank, you cannot use the item as a voice command. Setting the time difference The time difference can be set from “–4” to “+9” hours. DVD playback Touching o or p resumes normal playback at a desired point during continuous fast or is reverse/fast forward (when shown). [. . . ]