User manual PIONEER CDJ-100S

[. . . ] Operating Instructions COMPACT DISC PLAYER CDJ-100S CONTENTS CAUTIONS REGARDING HANDLING . . . . . . . . . . . . . . . . . . . . . 3 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PANEL FACILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4 CAUTION Do not attempt to press a disc back into the slot when the EJECT indicator appears. Pressing a disc back into the slot while the EJECT indicator appears may cause the player to stop. In this case, press the EJECT button again and wait until the EJECT indicator goes out before reinserting the disc. Insert straight 1. Set the rear-panel power switch to ON. Do not force a disc into the unit when the power switch is set to OFF as this may damage the disc and the unit. 2. Insert a disc. ¶ Hold the disc with label surface upwards, and insert into the front panel disc loading slot . ¶ When playing an 8 cm (3-inch) disc, place the disc in a commercially available CD adapter before inserting in the loading slot. Never attempt to load more than one disc at the same time, or attempt to load a second disc when one disc has already been loaded. ¶ When loading a disc, do not placing any twisting force on the disc, or try to force the disc into the slot. Also, do not attempt to interrupt or defeat the motion of the disc when the player begins to draw a disc into the slot or to eject a disc, since damage to the disc or player could occur. PRECAUTIONS ON PLAYING CD SINGLES (8 cm/3inch Discs) 1 When playing CD singles (8 cm/3-inch discs), always use the adapter for 8 cm/3-inch discs. Before loading the disc into the CD player, be sure to check that it is secured properly by the catches of the adapter. If discs have been inserted without the adapter by mistake, remove the disc immediately by pressing the eject button. 2 Use 8 cm/3-inch disc adapters labeled with the ' mark (recommended standard product). Do not use adapters which cause the disc to idle, nor adapters which are bent or curved. 8 <DRB1232> En BASIC OPERATION I ORDINARY CD PLAYER OPERATIONS To Pause Play During playback, press the PLAY/PAUSE button (6). ÷ The PLAY/PAUSE button's indicator and CUE indicator will flash, and play will be paused. ÷ When the PLAY/PAUSE button is pressed again, play will resume and the button indicator will light steadily. ÷ Broken sound will still be audible during the standby mode; if you wish to stop all sound, lower the output sound volume on your audio mixer. ÷ When the unit has not been operated for 80 minutes or more in pause mode, the disc rotation stops automatically. In this instance, playback can be resumed by pressing the PLAY/PAUSE button. Track Cueing Jog dial 7 TRACK SEARCH buttons (4, ¢ ) Setting the Auto Cue function ON/OFF Press and hold the TIME MODE/AUTO CUE button for one or more seconds to toggle the auto cue mode on and off. The auto cue function is turned on when the indicator light showing A. CUE is lit. Playback Operations These represent basic playback operations when the auto cue function is off (the display's A. CUE indicator goes off). 1. Insert disc. ÷ With the disc's label surface upward, insert the disc into the front-panel's disc loading slot. ÷ When playing an 8 cm/3-inch disc, place the disc in a commercially available CD adapter before inserting in the loading slot. CAUTION Do not attempt to press a disc back into the slot when the EJECT indicator appears. Pressing a disc back into the slot while the EJECT indicator appears may cause the player to stop. [. . . ] Check the error code with those listed in the table below to determine the cause of error. Contact your nearest Pioneer authorized service center if the cause of the error is unknown, too difficult to fix or if the same error code continues to display after the remedy has been tried. Refer to the error code when speaking to the Pioneer service representative. Displayed error code number E-72 01 E-72 02 E-83 01 E-83 02 E-91 01 E-91 03 Type of error TOC READ ERROR FG PULSE ERROR PLAYER ERROR PLAYER ERROR MECHANICAL TIME OUT MECHANICAL TIME OUT Error contents TOC date cannot be read after 20 seconds. [. . . ]