User manual PIONEER AVIC-9DVD-2 INSTALLATION MANUAL

[. . . ] ITALIANO NEDERLANDS 3 ENG/MASTER COVER 98 INST CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 2 IMPORTANT INFORMATION ABOUT YOUR NEW DVD NAVIGATION UNIT AND THIS MANUAL • The Pioneer DVD Navigation Unit is intended solely as an aid to you in the operation of your vehicle. It is not a substitute for your attentiveness, judgement and care while driving. € Do not use your navigation system to route you to emergency services such as hospitals or police stations. € Do not operate the DVD Navigation Unit if doing so will divert your attention from the safe operation of your vehicle. [. . . ] When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function. power cord Black , Orange/white , Red , Yellow ESPAÑOL ☞ See Page 11. DEUTSCH Yellow/black When combining this navigation unit with a Pioneer car stereo, if the car stereo has yellow/black leads, connect them to those leads. In this way, when the guidance audio is output and when you operate the system by voice, the vehicle stereo is automatically muted to reduce the vehicle stereo volume. Purple/white (REVERSEGEAR SIGNAL INPUT) This is connected so that the navigation system can detect whether the vehicle is moving forwards or backwards. Connect the purple/white lead to the lead whose voltage changes when the reverse gear is engaged. Unless connected, the sensor may not detect your vehicle travelling forward/backward properly, and thus the position of your vehicle detected by the sensor may be misaligned from the actual position. Note: When you use the ND-PG1 speed pulse generator (sold separately), please make sure to connect it. Check the position of your vehicle’s reversing lamp (the one that lights up when the gearstick is in reverse [R]) and find the reversing lamp lead in the boot. 10 11 ENG/MASTER 96 CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 12 Connecting the System Connecting the power cord (2) This product Note: Cords for this product and those for other products may be different colours even if they have the same function. When connecting this product to another product, refer to the supplied Installation manuals of both products and connect cords that have the same function. Be sure to install the unit in such a way that it will not obstruct driving. € Make sure that leads cannot get caught in a door or the sliding mechanism of a seat, resulting in a short circuit. € Please confirm the proper function of your vehicle’s other equipment following installation of the DVD navigation unit. ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS 12 ENG/MASTER 96 13 CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 14 Installation To guard against electromagnetic interference • In order to prevent interference, set the following items as far as possible from the main unit of this Navigation System, other cables or leads: - TV aerial and aerial lead - FM, MW/LW aerial and its lead - GPS aerial and its lead In addition you should lay each aerial lead as far as possible from other aerial leads. Such electromagnetic noise would increase the error for the location display. Before installing and fixing • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. € Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. Before using the adhesive tape • Make sure the surface is free of moisture, dust, grime, oil, etc. 13 ENG/MASTER 96 14 CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 15 Installing the main unit ENGLISH Installation notes • Do not install the main unit in places where it may become subject to high temperatures or humidity, such as: * Places close to a heater outlet. * Places exposed to direct sunlight, such as on top of the dashboard or the rear shelf. € The installation strength will depend on the vehicle model and the installation position. [. . . ] Make a U-shaped loop in the lead outside the rubber packing to prevent rainwater from flowing along the lead into the interior of the vehicle. ) Holder Double-sided tape (large) DEUTSCH Loading the batteries Remove the battery cover, and insert two alkaline (UM-4, AAA, LR03, 1. CAUTION • Take care to insert the batteries the right way round as shown by the + and marks in the diagram. € If the Remote Control will be out of use for a long period, remove the batteries. [. . . ]