User manual PHILIPS CE153DR

[. . . ] Always there to help you Register your product and get support at www. philips. com/welcome Question?Contact Philips CE153DR User manual Contents Contents 1 Safety 2 Your car audio system Introduction What's in the box Overview of the system 2 3 3 3 4 6 7 8 10 11 11 11 11 11 12 12 12 12 12 13 13 13 13 7 Play from a storage device Control play Switch tracks 18 18 19 19 19 19 20 20 21 21 22 22 23 23 24 24 24 24 25 26 26 27 28 28 28 28 29 8 Play from an iPod/iPhone 3 Install the car audio system Connect wires Mount into the dashboard Attach the front panel Compatible iPod/iPhone models Connect your iPod/iPhone Control play Charge your iPod/iPhone 9 Use Bluetooth devices 4 Get started For the first time use Set the time format Set the clock Select a source Select a listening zone Mute the button beep Connect a device Play audio from a Bluetooth device Make a call 10 Listen to an external player 11 Adjust sound 12 Additional information Reset the system Replace the fuse Upgrade the firmware 5 Listen to FM/MW radio stations Switch to FM/MW radio mode Select a tuner region Select a tuner sensitivity Search for a radio station Store radio stations in memory Play with RDS 13 Product information 14 Troubleshooting 6 Listen to DAB radio stations 15 Switch to DAB mode 15 Scan for on-air stations 15 Program radio stations 16 Display DAB information 16 Set up for weak reception 17 Use the DRC (Dynamic Range Control) 17 Disable the DAB reception 17 Reset the DAB tuner 17 Remove invalid stations 17 Check the current version of DAB firmware 17 General About the Bluetooth device 15 Notice Compliance Care of the environment Trademark notice Copyright EN 1 1 Safety Read and understand all instructions before you use this device. If damage is caused by failure to follow instructions, the warranty does not apply. • Modification of the product could result in hazardous radiation of EMC or other unsafe operation. [. . . ] • [CT ON]: Synchronize the system clock with the RDS station automatically. • [CT OFF]: The automatic clock synchronization with RDS station is disabled. Tip 1 2 Press and hold to access the system menu. » The detected stations are saved in the flash memory. • The accuracy of time depends on the RDS station that transmits time signals. EN 15 Tune to a detected station • 1 2 3 4 Press to exit the system menu. / repeatedly or rotate until the name of the target station is displayed. Press Press to start listening. To tune to a programmed radio station, press its corresponding numeric button , , , , , or . Program stations manually 1 2 3 Tune to the target detected station (see ‘Tune to a detected station’ on page 16). Press and hold a numeric button , , , , , or to assign a sequence number to the station. • To tune to a programmed radio station, press its corresponding numeric button , , , , , or . Program radio stations You can assign a sequence number to a detected station. Afterwards, you can quickly tune to it by pressing the corresponding numeric button on the main unit. Note • Before the programming, make sure that the scanning • You can store a maximum of six stations in each band. is complete. 4 Program stations automatically Display DAB information The name of current DAB station is displayed. • Dynamic label segment (DLS) • Signal strength • Program type (PTY) • Ensemble name • Frequency • Signal error rate • Bitrate codec • Time • Date 1 2 3 Press and hold to access the system menu. » The product starts programming DAB radio stations automatically. » Earlier programmed stations are replaced with the latest ones. » After the programming is complete, the first programmed station is broadcast. 16 EN Set up for weak reception When the current reception gets poor, the product can automatically switch the source or mute the speakers according to your setup. 3 1 2 3 Press and hold to access the system menu. • [WEAK MUTE]: Mute the speakers • [WEAK TO FM]: Switch the source to an FM radio station with strong reception that broadcasts the same program Rotate to select an option, and then press to confirm. • [ANTENNA 12V]: Enable the DAB reception. Reset the DAB tuner 1 Press and hold to access the system 2 menu. • To clear the list of detected and programmed stations, press to confirm. • To exit the system menu, press . Use the DRC (Dynamic Range Control) DRC adds or removes a degree of compensation for the differences in the dynamic range between radio stations. Remove invalid stations 1 Press and hold to access the system 2 menu. • To remove invalid stations from the list of scanned stations, press . • To exit the system menu, press . 1 2 Press and hold to access the system menu. Rotate to select an option. 3 Check the current version of DAB firmware 1 Press and hold to access the system 2 menu. » The current version of DAB firmware is displayed. Disable the DAB reception 1 Press and hold to access the system 2 menu. Press / repeatedly until [ANTENNA OFF] or [ANTENNA 12V] is displayed. EN 17 7 Play from a storage device This system can play . mp3 and . wma files that are copied onto a compatible storage device. Note • Philips does not guarantee compatibility with all storage • devices. NTFS (New Technology File System) file system is not supported. 2 3 Press AS/SOURCE repeatedly to switch the source. [. . . ] Check the USB storage device or SD/SDHC card. The paired mobile phone connects and disconnects constantly. Move the mobile phone closer to the system or remove any obstacle between the mobile phone and the system. • Some mobile phones may connect and disconnect constantly when you make or end calls. • For some mobile phones, the Bluetooth connection may be deactivated automatically as a power-saving feature. [. . . ]