User manual PANASONIC U-20ME1E81

[. . . ] Do not install the air conditioner where excessively high heat-generating objects are placed. Avoid: To protect the air conditioner from heavy corrosion, avoid installing the outdoor unit where salty sea water can splash directly onto it or in sulphurous air near a spa. Electrical Requirements 1. Each unit must be properly grounded with a ground (or earth) wire or through the supply wiring. The wires in this mains lead are colored in accordance with the following code: Green-and-Yellow: Earth Blue: Neutral Brown: Live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plugs, proceed as follows: The wire which is colored green and yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored green or green-and-yellow. The wire which is colored blue must be connected to the terminal which is marked with letter N or colored black. [. . . ] Never use your hands to move the flap (vertical airflow flap) that is controlled using the remote controller. When the air conditioner is turned off, the flap (vertical airflow flap) automatically moves to the downward position. The flap (vertical airflow flap) moves to the upward position when performing the standby operation for heating. The swing operation is made after the standby operation for heating is released, but swing is indicated on the remote controller even during the standby operation for heating. FLAP button is pressed during operation. Setting the airflow direction To activate the swing operation The airflow direction changes each time the Press the FLAP button to set the flap (vertical airflow flap) to the downward position, and then press the FLAP button again. In the cool mode, do not direct the flap down and move out of the cooling zone ?A?, otherwise, condensation may drip on to the floor. When operating continuously in the fixed airflow direction setting for about an hour, the airflow direction is automatically controlled and the flap position is changed. The airflow direction may be different from the display on the remote controller. for heating Indoor unit Horizontal directions (manual) The horizontal airflow direction can be adjusted manually by moving the vertical vanes to the left or right. Concealed duct type (F1, M1, E1) This air conditioner is not equipped with air outlet parts. Please refer to the manual of the locally adopted air outlet parts. OI-165-7-EN 7 01_F568453_EN. fm Page 8 Thursday, March 15, 2012 5:18 PM Adjusting the Airflow Direction for Multiple Indoor Units Using a Single Remote Controller (Wired) ?The airflow direction cannot be set using the remote controller for the concealed duct type (F1, M1, E1) and floor standing type (P1, R1). If multiple indoor units are connected to a remote controller, the airflow direction can be set for each indoor unit by selecting the indoor units (see the operation below). Set the airflow direction for the indoor unit that is shown on the display. Each time UNIT is pressed, the indicator changes in the order shown below. When nothing is displayed, you can make the setting for all indoor units in one operation. The unit number is displayed as Outdoor Unit Number?Indoor Unit Number. 1?3 8 OI-165-8-EN 01_F568453_EN. fm Page 9 Thursday, March 15, 2012 5:18 PM Special Remarks ??DRY??Once the room temperature reaches the level that was set, the unit repeats the cycle of turning on and off automatically. In order to prevent the humidity in the room from rising again, the indoor fan also turns off when the unit stops operating. operation is not possible if the outdoor temperature is 15 C or less. Heating Operation Heating performance ?Because this appliance heats a room by utilizing the heat of the outside air (heat pump system), the heating efficiency will fall off when the outdoor temperature is very low. [. . . ] (??) 120 12_F568453_Spec. fm Page 121 Tuesday, February 28, 2012 10:28 AM English Franais Compliance with regulation 842/EC/2006 Article 7(1) requirements DO NOT VENT R410A INTO THE ATMOSPHERE: R410A IS A FLUORINATED GREENHOUSE GAS, COVERED BY THE KYOTO PROTOCOL, WITH A GLOBAL WARMING POTENTIAL (GWP) = 1975. Conformit aux exigences de l?article 7 (1) de la rglementation 842/EC/ 2006 NE PAS METTRE LE R410A L?AIR LIBRE: LE R410A EST UN GAZ EFFET DE SERRE FLUOR, RGUL PAR LE PROTOCOLE DE KYOTO AVEC UN POTENTIEL DE RCHAUFFEMENT DE LA PLANTE (GWP) = 1975. Cumplimiento de los requisitos del Artculo 7 (1) de la Directiva 842/EC/ 2006 NO LIBERAR R410A AL AIRE LIBRE: EL R410A ES UN GAS FLUORIZADO DE EFECTOS DE INVERNADERO, INCLUIDO EN EL PROTOCOLO DE KYOTO, CON UN POTENCIAL DE CALENTAMIENTO GLOBAL (GWP) = 1975. Kompatibilitt mit den Anforderungen der Vorschrift 842/EC/2006, Artikel 7 (1) R410A NICHT IN DIE AUSSENLUFT ABLASSEN: R410A IST EIN FLUORIERTES TREIBHAUSGAS, DAS IM KYOTO-PROTOKOLL ENTHALTEN IST UND EIN ERDERWRMUNGSPOTENTIAL (GWP) VON 1975 AUFWEIST. [. . . ]