User manual PANASONIC S-710WX2E5

[. . . ] INSTRUCTION MANUAL Gas Heat Pump Chiller Water Heat Exchanger M1 Type S-250WX2E5 SGP-WE80M1 S-500WX2E5 SGP-WE170M1 S-710WX2E5 CONTENTS . . . . . . 18 22 Use a equipment properly and save energy 82664119401000 82664119378000 CHARACTERISTICS AND REQUESTS ABOUT YOUR GAS HEAT PUMP AIR CONDITIONER The gas heat pump air conditioner (GHP) uses gas as the fuel to drive the compressor. Even on very cold days the unit doesn't almost frost up so it provides stable heating operation. As the electric power consumption is about 3 kW, this leads to be less received power equipment. [. . . ] of the indoor/outdoor unit which an abnormality occurs. Appears while in test operation. 8 OPERATION Setting the Present Time 1. Press and hold for more than 2 seconds to enter in the present day and time setting mode. Once you enter in the setting mode, , “ ”(day) and “time” flash. Press *1 to move “ ” (flashing on the display) in the order of : Su → Mo → Tu → . . . . Press to move it in the order of : Su → St → Fr → . . . . *1 3, 4 1, 3, 4 2 While in time setting mode, the temperature setting buttons function as (changing day) button. to change the present “hour” in the range of 0 to 23*2. The “hour” digits light up, and the “minute” digits start flashing. *2 If the clock uses the 12 hours AM/PM setting, the hour is displayed in the range of AM 0 to 11/PM 0 to 11. 4. Press , to change the present “minute” in the range of 0 to 59. The day and time are set and finishes the setting mode. Note • The unit returns to the normal mode if is pressed or there is no operation made for 3 minutes during the setting. • If the present time is invalid, “– – : – –” is displayed. If the power failure for more than 1 hour occurs, check if the set data of day and time are valid. 9 Weekly Program Function Checking Weekly Timer Set the weekly program assigning a given timer to each day of the week. Select the day and the TIMER number you want to program. Program image diagram Vertical scale indicates the TIMER No. , and horizontal scale indicates the day. button Su Mo Tu We Th Fr Sa 1 2 3 4 5 6 Select a section from the 42 programs. 1. Press to enter the program confirmation mode “ ” and start setting. Once you enter the program confirmation mode, the present day is indicated as TIMER No. Press and / to move the “ ” horizontally on the day to select. Press to move “ ” (flashing on the display) in the order of : Su Mo Tu. . . . “– – : – –” is displayed when the program is not set. 1~6 10 Changing the Program Timer To set the weekly program, follow the steps below. The unit enters the confirmation mode, and press setting mode of the program currently displayed. , “hour”, “minute” * In the program setting mode, and “item” flash on the display. 2, 3, 4 1, 2, 3, 4 4 Program step1 2. The unit enters the program changing Confirm the “hour” and press (setting of the “minute”). . The unit enters Confirm the “minute” and press pattern selection mode). [. . . ] button Changes the operation mode after the sleeping function operation is cancelled. Sleeping function Off time In case the present time is 23:00. indication Display of remote control unit (during repetitive timer OFF function setting) Sleeping function indication * If no operation is made for 3 minutes, the time setting mode will be automatically finished. • Each time the button is pressed, the indication changes in the following order. (every one hour) (Press to stop the time setting. ) 2. • The sleeping operation starts. 15 • If button does not work. is pressed. Or if the operation does not start even if Check the following table. Item 1 Display of the remote control unit (Lighting/flashing indication) The Error indication flashes (for several seconds). [. . . ]