User manual PANASONIC PT-AT5000E

[. . . ] Operating Instructions Functional Manual   LCD Projector   Model No. PT-AT5000E Thank you for purchasing this Panasonic product. ■  efore operating this product, please read the instructions (Basic Guide / Functional manual) carefully and B save this manual for future use. ■ Please ensure you read the “Read this first!” ( pages 6 to 13) carefully prior to use. ENGLISH TQBJ0397 WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Select your required colour adjustment ([Y ADJUST], [R ADJUST], [G ADJUST], [B ADJUST]) with ▲ ▼ in the [GAMMA ADJUSTMENT] menu and press the <ENTER> button. GAMMA ADJUSTMENT PICTURE ADJUSTMENT MODE GAMMA HIGH POSITION GAMMA MID GAMMA LOW LANGUAGE POINT Y ADJUST 3D SETTINGS R ADJUST G ADJUST LENS CONTROL B ADJUST INITIALIZE OPTION ADVANCED INPUT POINT 5 INPUT 50% OUTPUT +10 5 Y ADJUST 0% 50% 100% OUTPUT MOVE UP R ADJUST INPUT 0% 50% 100% OUTPUT POINT 5 INPUT 50% OUTPUT +30 Setting range: -252 to +252 INPUT POINT 5 INPUT 50% OUTPUT +10 e. Setting the output levels back to the default setting zz To set the output level on the selected point back to the default setting “0”, press the <DEFAULT> button on the remote control. Note zz Individual input levels cannot be set back to their default settings by pressing the <DEFAULT> button. ▲ ▼ ENGLISH - 47 Adjustment and Settings [PICTURE] menu ● ● Initialize the gamma adjustment results GAMMA ADJUSTMENT PICTURE ADJUSTMENT MODE GAMMA HIGH POSITION GAMMA MID GAMMA LOW LANGUAGE POINT Y ADJUST 3D SETTINGS R ADJUST G ADJUST LENS CONTROL B ADJUST INITIALIZE OPTION GAMMA HIGH GAMMA MID 0 0 0 ADVANCED GAMMA LOW 5 [ADVANCED MENU] items [GAMMA HIGH] [GAMMA MID] [GAMMA LOW] zz Setting range: -8 to +8 Default setting 0 0 0 1111 Press the ▲▼ buttons to select [INITIALIZE] and press the <ENTER> button. ■■[CONTRAST] You can adjust colour temperatures centring mainly on white. R (RED), G (GREEN), B (BLUE) zz The confirmation screen is displayed for the gamma initialization. GAMMA ADJUSTMENT INITIALIZE GAMMA ADJUSTMENT. OK CANCEL -1 +1 Default setting 0 0 0 [ADVANCED MENU] items 2222 Select [OK] with the the <ENTER>button. buttons and press ▲ ▼ [CONTRAST R] [CONTRAST G] [CONTRAST B] zz Setting range: -32 to +32 zz Your gamma settings in [ADVANCED] mode will return to factory default settings. Note zz Initialize is not available in [SIMPLE] mode. ● ●Adjusting the gamma (when [SIMPLE] is selected for [ADJUSTMENT MODE]) 1111 Press the ◄► buttons to select [SIMPLE]. GAMMA ADJUSTMENT PICTURE ADJUSTMENT MODE GAMMA HIGH POSITION GAMMA MID GAMMA LOW LANGUAGE POINT Y ADJUST 3D SETTINGS R ADJUST G ADJUST SIMPLE 0 0 0 ■■[BRIGHTNESS] You can adjust colour temperatures centring mainly on black. R (RED), G (GREEN), B (BLUE) zz You can adjust linear intensity at 3 levels (high, mid, low). Press ▲ ▼ to select your required gamma levels. ▲ ▼ Adjustment and Settings -1 +1 Default setting 0 0 0 [ADVANCED MENU] items [BRIGHTNESS R] [BRIGHTNESS G] [BRIGHTNESS B] zz Setting range: -16 to +16 2222 Select item with the ▲▼ buttons, and adjust with the buttons. ■■[NR] You can eliminate the noise that occurs when the input signal deteriorates. -1  +1 Weaken zz Setting range: 0 to +3 Strengthen 48 - ENGLISH [PICTURE] menu ■■[MPEG NR] You can eliminate the noise that occurs upon projection for videos that use MPEG compression. ■■[COLOUR MANAGEMENT] For the selected [PICTURE MODE], you can adjust a selected colour individually with [CURSOR] mode or adjust the six colour components (Red, Green, Blue, Cyan, Magenta, Yellow) with [RGBCMY] mode. Adjustment results can be saved as a profile and called later. Weaken zz Setting range: 0 to +3 Strengthen ● ●Create a new profile Note zz [COLOUR MANAGEMENT] will be unable to adjust with the setting of [REC709] in [PICTURE MODE], when HDMI signal is selected. zz When the input signal is switched while adjusting, adjustment details are not saved. zz If there is another area, which has the exact same or similar colour as the target on the same screen, these colours will be adjusted as well. zz If you edit a single colour to be individual different colours, the desired colour may not be achieved. zz When a 3D signal is being input (including converting 2D to 3D), [COLOUR MANAGEMENT] cannot be executed. Attention zz Use a strong setting when projecting an MPEG video. zz COMPUTER (RGB) signal is not supported. ■■[FRAME CREATION] You can activate the rendering system for fast motion frames with fewer afterimage. Switch settings Switch settings [OFF] [MODE3] [OFF] [MODE1] [MODE2] [MODE3] Note Deactivate [MODE1] [MODE2] zzAdjusting the selected colour (when [CURSOR] is selected for [ADJUSTMENT MODE]) Select the desired colour with a cursor and adjust. Setting for a standard image Setting for a cinema image Setting for a fast moving image 1111 Press the ◄► buttons to select [CURSOR] in [ADJUSTMENT MODE]. COLOUR MANAGEMENT PROFILE ADJUSTMENT MODE START ADJUSTMENT LOG 2222 Press the ▲▼ buttons to select [START ADJUSTMENT] and press the <ENTER> button. zz The cross cursor (A) is displayed, and the projected image is captured.  Screen 3333 Move the cursor with the ▲▼◄► buttons to the required place to select a colour. zz Align the centre of the cross cursor on the point in the projected image to be adjusted. ENGLISH - 49 Adjustment and Settings zz With some of the images, it might be difficult to see a difference in result. zz If [FRAME CREATION] is set to active, video may be delayed in some cases. zz This cannot be set to active when [2D TO 3D] ( page 66) is enabled. NORMAL CURSOR [PICTURE] menu 4444 Press the <ENTER> button. zz [CURSOR] menu (B) and the colour selected (C) are displayed. CURSOR ENTER DEFAULT SELECT RETURN ● ● Adjusting the selected colour (when [RGBCMY] is selected for [ADJUSTMENT MODE]) Select the colour from 6 different colour types ([RED], [GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW]) and adjust [COLOUR], [TINT] and [BRIGHTNESS]. COLOUR TINT BRIGHTNESS 0 0 0 1111 Press the ◄► buttons to select [RGBCMY] in [ADJUSTMENT MODE].  Screen Note zz In some cases you may be unable to adjust when the very edge point of the projection area is selected. zz You can create a profile only when [ADJUSTMENT MODE] is set to either [CURSOR] or [RGBCMY]. zz White, gray and black cannot be edited. COLOUR MANAGEMENT PROFILE ADJUSTMENT MODE START ADJUSTMENT LOG NORMAL RGBCMY 2222 Press the ▲▼ buttons to select [START ADJUSTMENT] and press the <ENTER> button. 3333 Press the ▲▼ buttons to select your desired colour and press the <ENTER> button. RGBCMY ADJUSTMENT RED GREEN BLUE CYAN MAGENTA YELLOW 5555 Press the ▲▼ buttons to select a menu item and the ◄► buttons to adjust each item level. [COLOUR] Adjust the vividness of the colour. zz Setting range: −30 to +30 zz Setting range: −30 to +30 [TINT] Adjust the colour tone. Adjust the brightness of the colour. zz Setting range: −20 to +20 [BRIGHTNESS] zz Menu (B) and the base colour (C) is displayed. zz The default setting for each item is [0]. After adjusting, the post-adjustment colour (D) is displayed. CURSOR ENTER DEFAULT SELECT RETURN Adjustment and Settings RED ENTER DEFAULT SELECT RETURN COLOUR TINT BRIGHTNESS 0 0 0 COLOUR TINT BRIGHTNESS 0 0 0  Screen  Screen 6666 Press the <ENTER> button. zz [PROCESSING] message is displayed for a few seconds and the result is stored in [LOG]. [. . . ] **** For details of video signals that can be projected with this projector, see the “List of compatible signals” ( page 95). Appendix 100 - ENGLISH Specifications S-VIDEO IN VIDEO IN 1 set, Mini DIN 4p Y: 1. 0 V [p-p], C: 0. 286 V [p-p], 75 Ω 1 set, RCA pin jack 1. 0 V [p-p], 75Ω 1 set, D - sub HD 15-pin (female) (RGB signal) R. G. B. G. SYNC HD/SYNC*1 0. 7 V [p-p], 75 Ω 1. 0 V [p-p], 75 Ω TTL high impedance, automatic positive/negative polarity compatible TTL high impedance, automatic positive/negative polarity compatible 1. 0 V [p-p] (including sync), 75 Ω 0. 7 V [p-p], 75 Ω 1. 0 V [p-p] (including sync), 75 Ω 0. 7 V [p-p], 75 Ω COMPUTER IN VD*1 Terminals (Y, PB/CB, PR/CR signal) Y: PB/CB, PR/CR 1 set, RCA pin jack x 3 COMPONENT IN HDMI IN SERIAL TRIGGER / 3D SHUTTER OUT Cabinet Dimensions Weight Certifications Power supply Operating range Remote control Weight Dimensions Y: PB/CB, PR/CR 3 sets, 19-pin HDMI connector (HDCP/HDAVI Control Ver. 5 compliant) 1 set, D-sub 9-pin RS-232C compatible 2 sets, monaural mini jack DC 12 V, max. 100 mA (Selectable for input and output by menu operation. ) Moulded plastic (PC+ABS) Width Height Depth Approx. 8. 7 kg (19. 18 lbs. ) *2 470 mm (18 1/2") 151 mm (5 15/16") 364 mm (14 11/32") EN60950-1, EN55022, EN61000-3-2, EN61000-3-3, EN55024 DC 3 V (AA/R6/LR6 battery x 2) Approx. [. . . ]