User manual PANASONIC DMC-FT20

[. . . ] Basic Operating Instructions Digital Camera Model No. DMC-FT20 Before use, please read these instructions completely. More detailed instructions on the operation of this camera are contained in "Operating Instructions for advanced features (PDF format)" in the supplied CD-ROM. Install it on your PC to read it. Web Site: http://www. panasonic-europe. com Model number suffix "EB" denotes UK model. VQT4A91 EB F0112HY0 Dear Customer, We would like to take this opportunity to thank you for purchasing this Panasonic Digital Camera. Please read these Operating Instructions carefully and keep them handy for future reference. of your Digital Camera may look somewhat different from those shown in the illustrations in these Operating Instructions. [. . . ] (You can purchase the accessories separately. ) (ENG) VQT4A91 9 Sales and Support Information Customer Communications Centre · For customers within the UK: 0844 844 3899 · For customers within Ireland: 01 289 8333 · For further support on your product, please visit our website: www. panasonic. co. uk Direct Sales at Panasonic UK · Order accessory and consumable items for your product with ease and confidence by phoning our Customer Communications Centre Monday­Thursday 9:00 a. m. ­5:30 p. m. , Friday 9:30 a. m. ­5:30 p. m. (Excluding public holidays) · Or go on line through our Internet Accessory ordering application at www. pas-europe. com. · All enquiries transactions and distribution facilities are provided directly by Panasonic UK. (If failure occurs during the test, a new set is used to pass the drop orientation test within a total of 5 devices) Panasonic's test method is based on the above "MIL-STD 810F Method 516. 5-Shock". However, the drop height was changed from 122 cm (4 feet) to 150 cm (5 feet) dropping onto 3 cm (0. 1 feet) thick plyboard. (Disregarding appearance change such as loss of paint or distortion of the part where drop impact is applied. ) (ENG) VQT4A91 11 Handling of the camera · Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or dropped etc. If an impact to the camera occurs, it should be inspected (subject to a fee) by a Panasonic's Service Centre to verify that the waterproofing is still effective. · When the camera is splashed with detergent, soap, hot spring, bath additive, sun oil, sun screen, chemical, etc. , wipe it off immediately. · Waterproof function of the camera is for sea water and fresh water only. · Any malfunction caused by customer misuse, or mishandling will not be covered by the warranty. · Supplied accessories are not waterproof (excluding Hand Strap). · Do not leave the camera for a long period of time in places where temperature is very low (at ski resorts or at high altitude etc. ) or very high [above 40 oC (104 oF)], inside a car under strong sunlight, close to a heater, on the beach, etc. Waterproof performance may be degraded. About the [Precautions] demonstration display ([Requirements for Underwater use]) · [Precautions] is displayed when the power is turned on for the first time after purchase, with · Please check beforehand to maintain the waterproof performance. the side door completely closed. 1 2 Press 2 to select [Yes], and press [MENU/SET]. 2: 1: Return to the previous screen View the next screen · It will automatically skip to the clock setting screen if [No] is selected before it starts. · It can be forcefully ended by pressing [MENU/SET]. · When it is forcefully ended while checking by turning the unit off or pressing [MENU/ SET], [Precautions] is displayed every time the power is turned on. 3 After the final screen (12/12), press [MENU/SET] to finish. · When [MENU/SET] is pressed after the final screen (12/12), [Precautions] is not · This can also be viewed from [Precautions] in the [Setup] menu. displayed from the next time the power is turned on. 12 VQT4A91 (ENG) Check before using underwater Do not open or close the side door in places with sand and dust, close to water, or with wet hands. Sand or dust adhering may cause water leaks. 1 Check that there are no foreign objects on the inner side of the side door. A Brush (supplied) B Side door · If there is any foreign object, such as lint, hair, sand, etc. , on the surrounding area, water will leak within a few seconds causing malfunction. It may cause water leaks and malfunction if you use the camera with liquid adhered. · If there is any foreign material, remove with supplied brush. · Remove large foreign objects, wet sand, etc. , using the shorter (harder) side of the brush. 2 Check for cracks and deformation of the rubber seal on the side door. · The integrity of the rubber seals may decrease after about 1 year, with use and age. To avoid permanently damaging the camera the seals should be replaced once each year. Please contact Panasonic's Service Centre for related costs and other information. 3 Close the side door securely. C [LOCK] switch (grey part) D Red part E Released state F Locked state · Lock the [LOCK] switch securely until the red part is no longer visible. · To prevent water seeping into the camera, be careful not to trap foreign objects such as liquids, sand, hair or dust etc. (ENG) VQT4A91 13 Using the camera underwater · Use the camera underwater to 5 m (16 feet) with the water temperature between 0 oC and · Do not use for scuba diving (Aqualung). [. . . ] (Compatible OS: Windows XP SP3/Windows Vista SP2/Windows 7) · You can download and install a version of Adobe Reader that you can use with your OS from the following Web Site. http://get. adobe. com/reader/otherversions/ 22 VQT4A91 (ENG) Installing supplied software · The supplied CD-ROM includes the following software. ­ PHOTOfunSTUDIO 8. 0 SE (Windows XP/Vista/7) ­ LoiLoScope 30 day full trial version (Windows XP/Vista/7) · Before inserting the CD-ROM, close all running applications. (This will only install a shortcut to the trial version download site. ) Check the environment of your PC. · Operating environment of "PHOTOfunSTUDIO 8. 0 SE" ­ OS: WindowsR XP (32bit) SP3, Windows VistaR (32bit) SP2, WindowsR 7 (32bit/64bit) and SP1 PentiumR III 500 MHz or higher (WindowsR XP), PentiumR III 800 MHz or higher (Windows VistaR), PentiumR III 1 GHz or higher (WindowsR 7) 1024k768 pixels or more (1920k1080 pixels or more recommended) ­ CPU: ­ Display: ­ RAM: ­ Free hard disk space: operating environment. 512 MB or more (WindowsR XP/Windows VistaR), 1 GB or more (WindowsR 7 32bit), 2 GB or more (WindowsR 7 64bit) 450 MB or more for installing software · Refer to the operating instructions of "PHOTOfunSTUDIO" (PDF) for further Insert the CD-ROM with the supplied software. [. . . ]