User manual PANASONIC CQ-DP655EW

[. . . ] This could cause electrical shorts, fire, or other damage. Use Authorized Servicenters Do not attempt to disassemble or adjust this precision product. Please refer to the Servicenter list including with this product for service assistance. When Parked Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on. For Installation This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30x. Use the Proper Power Supply This product is designed to operate with a 12 V DC, negative ground battery system. Components Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation hardware. . . . . . . . . . . . . . . . 1 set ( page 19) Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If not, keep testing different lead combinations until you have located all the speaker leads. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. Follow the diagram carefully to avoid damaging the speakers and the stereo unit. The speakers used must be able to handle more than 45 W of audio power. If using an optional audio amplifier, the speakers should be able to handle the maximum amplifier output power. Speaker impedance should measure 4­8 , which is typically marked on most speakers. Lower or higher impedance speakers will affect output and can cause both speaker and stereo unit damage. Motor Antenna Connect the car motor antenna lead to the dark blue motor antenna relay control lead. Battery Connect the yellow battery lead to the correct radio wire or to the battery fuse port on the fuse block. The dashboard should be 4. 75 mmj5. 56 mm thick in order to be able to support the unit. Final Installation Lead Connections Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. After making a few final checks, you're ready to enjoy your new auto stereo system. 20 CQ-DP655EWW CQ-DP655EWW 21 E N G L I S H 13 Installation Guide (Continued) Installation Procedures First complete the electrical connections, and then check them for correctness. ( pages 25, 26) Remove the Unit E N G L I S H 14 1 Insert mounting collar 1 into the dashboard, and bend the mounting tabs out with a screwdriver. Make sure that the lock lever (§) is flush with the mounting collar 1 (not projecting outward). The be opened. 45WX4 OPEN Main unit Contact 1 Open RANDOM REP PWR 2 Push 3 Pull out 2 Push the face plate to the left. 6 Power connector Lock lever (§) 2 Remove the trim plate 8 with a screwdriver. Mounting tabs 5 Mounting bolt 8 Trim plate Screwdriver 1 2 2 3 4 Secure the rear of the unit. After fixing mounting bolt 5 and power connector 6, fix the rear of the unit to the car body by either method (a) or (b) shown below. After installation, reconnect the negative - battery terminal. unit while pushing 3 Pull out the screwdriver. down the lock lever with a Lock lever (a) Using the rear support strap 3 Fire wall of car 4 Tapping screw (5 mm·a16 mm) 3 mm· 2 Hex. nut (5 mm·) 3 Rear support strap 5 Mounting bolt (5 mm·) 1 Mounting collar (b) Using the rubber cushion (option) Rear support bracket Rubber cushion (option) (provided on the car) Lock lever 4 Remove the unit pulling with both hands. 5 Mounting bolt (5 mm·) 1 Mounting collar 22 CQ-DP655EWW CQ-DP655EWW 23 E N G L I S H 15 Anti-Theft System This unit is equipped with a removable face plate. [. . . ] Turn off the car engine (ACC off) and remove the fuse from the battery lead (yellow) for 1 minute. caused by noise) Clean disc, referring to the section on "Notes on CD/CD media (CD-R, CD-RW)". The unit may not successfully play back a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. Mount the unit securely with the mounting parts, referring to the section on installation. [. . . ]