User manual PANASONIC CQ-DP171U

[. . . ] ® APM FOLDER VOL BAND TUNE TRACK CQ-DP171U CD RECEIVER WITH CHANGER CONTROL PWR SEL DISP SOURCE REMOTE RANDOM SCAN REPEAT MUTE 1 2 3 4 5 6 LOUD Removable Full Front CD Player/Receiver with Changer Control Lecteur CD/Récepteur avec commande de changeur de CD et panneau avant entièrement amovible Reproductor de CD/Receptor con carátula completa desmontable y control de cambiador de CD CQ-DP171U Operating Instructions Manuel d'instructions Manual de instrucciones TEXT ¡Please read these instructions carefully before using this product and keep this manual for future use. ¡Prière de lire ces instructions attentivement avant d'utiliser le produit et garder ce manuel pour l'utilisation ultérieure. ¡Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro. E N G L I S H Safety Information Radio Frequency Interference Statement (Part 15 of the FCC Rules) : Applies only in U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 of the FCC Rules. ¡These limits are designed to provide reasonable protection against harmful interference in an automobile installation. [. . . ] Needed for in-dash installation. Required Tools You'll need a screwdriver, a 1. 5 V AA battery, and the following: 12 V DC Test bulb Electrical tape Side-cut pliers Overview This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above). If you encounter problems, please consult your nearest professional installer. Dashboard Specifications Thickness Min. 7/32" (5. 56 mm) 2 3/32" (53 mm) 7 5/32" (182 mm) 24 CQ-DP171U Identify All Leads The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Power Lead If your car has a radio or is pre-wired for one : Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows: Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 16 Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If your car is not wired for an audio unit : Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN). Battery Lead If your stereo unit has a yellow lead, you will need to locate the car's battery lead. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function. ) If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. If your car is not wired for an audio unit : Go to the fuse block and find the fuse port for the battery, usually marked BAT. There are two leads for each speaker which are usually color coded. Connect All Leads Now that you have identified all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram (a page 30) shows the proper connections and color coding of the leads. [. . . ] Root folder is not included. ) Note: If the total of files and folders exceeds 254, successful playback may not be performed. E N G L I S H 30 Supported file systems and file names Supported file system ISO 9660 Level 1 ISO 9660 Level 2 Joliet* Romeo Apple Extension to ISO 9660 Displayable folder names and file names Name files and folders in accordance with the standard of each file system. ¡This player can display file names of up to 31 ASCII character set in scroll mode. * Up to 15 letters can be displayed when scrolling in the Joliet system. According to the standard, "á", "ç", etc. [. . . ]