User manual PANASONIC CQ-DF800W

[. . . ] If no operation takes place for more than 7 seconds in audio setting, the display returns to the regular mode. Balance and Fader You can adjust the sound balance among the front, rear, right and left speakers. Default: BAL (balance) CNT (center) FAD (fader) CNT (center) Setting range: 15 levels each Select [VOL "]: Right enhanced. [VOL #]: Rear enhanced. Subwoofer Level You can change the subwoofer volume level. Default: 0 dB Setting range: MUTE (subwoofer mute) j6 dB to i6 dB (by 2 dB) Select [VOL "]: Increases the level. [. . . ] Check the disc. Remote Control Unit Trouble Cause/Step Battery polarities are reversed. If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs. Check the disc. Buttons are invalid for operation. MP3/WMA § The player for some reason cannot read the file you are trying to play. (File recorded in an unsupported file system, compression scheme, data format, file name extension, damaged data, etc. ) Select a file that the player can read. Create a new disc if necessary. WMA § An attempt has been made to play a copy-protected WMA file. Play WMA files which are not copy-protected. No disc is in the player. Insert a disc in the player. § If all the files cannot be played, E4 or E5 remains on the display. 40 CQ-DF783/DFX403U CQ-DF783/DFX403U 41 E N G L I S H 27 Troubleshooting (continued) CD Changer Display Cause/Step Disc is dirty, or is upside down. (The changer automatically switches to the next disc. ) Disc has scratches. (The changer automatically switches to the next disc. ) No operation by some cause. If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs. The dual changer control unit is connected, and the connections are now being checked. Panasonic Servicenter List for Service Directory . . . Keep for future reference in case the product needs servicing. Installation Hardware. . . Needed for in-dash installation. Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN). Battery Lead If your stereo unit has a yellow lead, you will need to locate the car's battery lead. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function. ) If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. Connect All Leads Now that you have identified all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram (page 50) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Important: Connect the red power lead last, after you have made and insulated all other connections. [. . . ] [OPEN] Anti-Theft System This unit is equipped with a removable face plate. The security indicator will blink. E N G L I S H 34 1 Open. Contact Place the Removable Face Plate into Case 1 Switch off the power of the unit. Place the face plate into the case and take it with you when you leave the car. 7 Removable face plate case 2 Push. 3 Pull it out toward you. out. Install Removable Face Plate 1 Fit the face plate with its left hole on one of the Contact 2 Remove the trim plate 8 with a screwdriver. Screwdriver pins provided on the main unit. [. . . ]