User manual PANASONIC AJ-HDC27F

[. . . ] Camera/VTR AJ- P Operating Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with Part 15 of the FCC Rules. To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] While the HOLD button is held down, the VITC user's bit information appears on the counter display. 01:12:01:50 O When the camera's video signals are being recorded Recorded frame number count This indicates the number of frames recorded. When the frame rate has been set to 24 fps and recording has been performed for 10 seconds, "0240" will be displayed as the count. When recording is started, the count is reset to "0000, " and the number of recorded frames per cut is counted up to "9999. " Frame rate information 24 fps (23. 98 fps) Frame frequency 5: 59. 94 Hz 6: 60. 00 Hz Tape management information OActive frame information OREC START/STOP mark 02:40:24:50 65 How to use the user data The contents of the setting menus can be saved in the user area of the camera's memory, and they can be loaded from this area. Use of this data speeds up the process of reproducing suitable setup statuses. Loading the user data operations (pages 84 to 86), 1 Perform the menu "CAM CARD READ/WRITE" and display the screen of FILM (CAM) MAIN MENU 3. A AD EDWIE n< C M C R R A / R T > SLC EET : 1 RA ED SLC EET : 1 WIE RT CR CNI AD OFG TTERA IL ED RA UE DT ED SR AA TTE IL: 1 : 2 : 3 : 4 : User data operation Menus are used to save the setting menu contents in the user area of the camera's memory and load them from this area. Saving the user data operations 86), 1 Perform the menu"INITIALIZE"(pages 84oftoFILM and display the screen (CAM) MAIN MENU 4. NTAIE n< I I I L Z > RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E RA ED WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 5 : 6 : 7 : 8 : : 1 button to 2 Turn the JOG dial USER DATAmove the arrow (cursor) to the READ item. <CMCR RA/RT > A AD EDWIE SLC EET : 1 RA ED SLC EET : 1 WIE RT CR CNI AD OFG TTERA IL ED ED SR AA n RA UE DT TTE IL: 1 : 2 : 3 : 4 : to move 2 Turn the JOG dial button DATA item. the arrow (cursor) to the WRITE USER 5 : 6 : 7 : 8 : JOG dial 3 When theappears. button is pressed, the following 3 When the JOG dial button is pressed, the following message message appears. WIE?ED YS E N O n dial button the arrow 4 Turn the JOG and press theto move button. (cursor) to YES, JOG dial (cursor) to YES, JOG dial The data settings are saved in the user area of the camera's memory. The data settings saved in the user area of the camera's memory are loaded, and the settings are completed. 5 Presssetting menu is cleared, and the displays The showing the unit's current statuses appear at the top and bottom of the viewfinder screen. setting has been 6 When theit frame frequency restart the unit by changed, is necessary to turning the POWER switch to OFF and then to ON again for the setting to be switched. 5 After the data has been saved, press the MENU button twice. The setting menu is cleared, and the displays showing the unit's current statuses appear at the top and bottom of the viewfinder screen. 66 How to use the scene file The contents of the setting menus can be saved in the scene file area of the camera's memory, and they can be loaded from this area. Use of this data speeds up the process of reproducing suitable setup statuses. 5 Turn the JOG dial button to move the arrow (cursor) to the WRITE item. <IIILZ > NTAIE RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E RA ED RT n WIE RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 : 2 Scene file operation Menus are used to save the setting menu contents in the scene file area of the camera's memory and load them from this area. Saving the scene file JOG dial operations 86), 1 Perform the menu"INITIALIZE"(pages 84oftoFILM 6 When theappears. button is pressed, the following message and display the screen (CAM) MAIN MENU 4. NTAIE n< I I I L Z > RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E RA ED WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA TTE IL WIE?move the arrow (cursor) to the SCENE SEL dial button the arrow 7 Turn the JOG and press theto move button. (cursor) to YES, JOG dial The data settings are saved in the scene file area of the camera's memory. button 3 When the JOG dialflashing. is pressed, the scene 8 After the data has been saved, press the MENU file number starts Turn the JOG dial button twice. button to select the scene file in which data is to be saved. <IIILZ > NTAIE RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E n RA ED WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 The setting menu is cleared, and the displays showing the unit's current statuses appear at the top and bottom of the viewfinder screen. : 1 4 Press the JOG dial button to enter the scene file. 67 How to use the scene file Loading the scene file operations 86), 1 Perform the menu"INITIALIZE"(pages 84oftoFILM and display the screen (CAM) MAIN MENU 4. NTAIE n< I I I L Z > RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E RA ED WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 JOG dial 6 When theappears. button is pressed, the following message <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA : 1 TTE IL RA ?ED YS E N O n : dial button the arrow 7 Turn the JOG and press theto move button. (cursor) to YES, JOG dial The data settings saved in the scene file area of the camera's memory are loaded, and the settings are completed. 2 Turn the JOG dial button to move the arrow (cursor) to the SCENE SEL item. the MENU button twice. button 3 When the JOG dialflashing. is pressed, the scene 8 Presssetting menu is cleared, and the displays The file number starts Turn the JOG dial button to select the scene file whose data is to be loaded. <IIILZ > NTAIE RA FCOYDT ED ATR AA WIEUE DT RT SR AA CN E n SEESL RA ED WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 showing the unit's current statuses appear at the top and bottom of the viewfinder screen. : 1 4 Press the JOG dial button to enter the scene file. button 5 Turn the JOG dial item. to move the arrow (cursor) to the READ <IIILZ > NTAIE RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E ED n RA WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 : 2 68 How to use the scene file Resetting the scene file operations 86), 1 Perform the menu"INITIALIZE"(pages 84oftoFILM and display the screen (CAM) MAIN MENU 4. NTAIE n< I I I L Z > RA FCOYDT ED ATR AA WIEUE DT RT SR AA SEESL CN E RA ED WIE RT RST EE TTE: IL1 TTE: IL2 TTE: IL3 TTE: IL4 JOG dial 6 When theappears. button is pressed, the following message <CMCR RA/RT > A AD EDWIE RA ED SLC EET : 1 WIE RT SLC EET : 1 CR CNI AD OFG RA UE DT ED SR AA : 1 TTE IL RST?EE YS E N O n : dial button the arrow 7 Turn the JOG and press theto move button. [. . . ] source, and 4 Point the microphones at the soundaudio levels check that the changes in the displayed on the audio level meter of the display window and in the viewfinder reflect the changes in the strength of the sound. This inspection can also be performed for each channel by connecting one of the microphones to each channel in turn. 3. Manual audio level adjustment function inspection 1 Set the AUDIO IN CH1 and CH2 switches to FRONT. 2 Set the AUDIO SELECT CH1 and CH2 switch to MAN. level displays increase. 6. [. . . ]