User manual PALSONIC MODEL 3498
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PALSONIC MODEL 3498. We hope that this PALSONIC MODEL 3498 user guide will be useful to you.
Manual abstract: user guide PALSONIC MODEL 3498
Detailed instructions for use are in the User's Guide.
[. . . ] Never
remove covers unless qualified to do so; this unit contains dangerous voltages.
WARNING:
. LOCATE appliance in the room where direct light does not strike the screen. ALLOWexcessive warm and dustythe applianceprevent possible permit proper ventilation. CONNECT the appliance to AC 240 Volts, 50Hz
MAINS (AC) OPERATION
The wires in this mains lead are coloured in accordance with the following code. [. . . ] NOTE: During presetting, auto presetting will be cut off if any one of STAND BY button, PRESET ON/OFF button or AUTO PRESET button is pressed.
. * If "SKIP" displays on the screen, press "SKIP" button on the front panel to exit "SKIP" mode.
SKIP
llllllllllllll
8 SKIP
llllllllllllll
8 VHFH
3. Press and hold MANUAL TUNING button until your desired program appears.
VHFL VHFH UHF
MFT
VHFL
VHFH
UHF
5
4. The searched program station has been memorised at the present channel position, 5. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased. * If some channel position is tuned by MANUAL TUNING mode, AFC (automatic frequency control) function is defeated in this channel position.
. FUNCTION:
SKIP BUTTON:
When CHANNEL SELECTOR button is used to select channels, the channel will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing.
CHANNEL INCREASE CH 1 2 58 59 CH
CHANNEL DECREASE (REMOTE) 1 2 58 59 (THE APPLIANCE)
. Press "SKIP" button, "SKIP" will be displayed on the screen to indicate that the channel is at "SKIP" mode.
SKIP
llllllllllllll
4. VOLUME CONTROL
Press the Press the
SOUND CONTROL:
(VOL) button to increase volume; the red block on the screen moves right. (VOL) button to decrease volume; the red block on the screen moves left.
. MUTE BUTTON (REMOTE CONTROL UNIT)
When there is a phone-call or a visitor, it can temporarily shut off the sound without affecting the picture. Press the PICTURE CONTROL button on the Remote Control Unit.
CONTRAST
PICTURE CONTROL (REMOTE CONTROL UNIT)
The FUNCTION to be adjusted is selected in sequence as shown in the following chart at every press of the button.
BRIGHTNESS
COLOUR
. Adjust the
button to obtain satisfactory picture.
ON SCREEN DISPLAY
Red Block Moves
CAPTION FUNCTION DISPLAY
Press
button
Press
button
Contrast Brightness Colour
CONTRAST BRIGHTNESS COLOUR
Weak Dark Pale
Strong Light Deep
CALL BUTTON (REMOTE CONTROL UNIT)
Press this button, the present channel number will be displayed on the screen. If the electronic clock is in operation, the channel and time will be displayed together at the upper right corner of the screen. Press STAND BY button, the appliance is set to stand by mode, the power indicator . BY button again, the appliance is turned on and the indicator is turned off. Using SLEEP button allows you to have the appliance automatically turned off a
predetermined time, and set the appliance to stand by mode.
SLEEP
Press again
SLEEP BUTTON (REMOTE CONTROL UNIT)
SLEEP 0 (RED)
SLEEP 90 (GREEN) Decrease 10 minutes at every press
SLEEP 10 (GREEN)
. After the SLEEP function is set, the remaining time will be automatically displayed for 4
seconds every ten minutes. * If you press STAND BY button while the SLEEP function is operating, the SLEEP function will be cancelled automatically.
TIMER OPERATION (REMOTE CONTROL UNIT)
Using TIMER button to select one of three timer modes, which are CLOCK mode, ON TIMER mode and OFF TIMER mode respectively.
TIMER
Press CLOCK AM 12 : 00 1 ON TIME AM 12 : 00
Press again OFF TIME AM 12 : 00
. [. . . ] The appliance will be turned off when your setting time is up, and return to stand by mode. * The OFF TIME function will be ineffective if the following conditions occurs; Press STAND BY button before the setting time is up. Switch off the power before the setting time is up.
TV/AV SELECTOR (REMOTE CONTROL . Press TV/AV button to change TV mode to AV mode, then UNIT) will be displayed in "VIDEO"
.
the upper comer of the screen for 4 seconds. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PALSONIC MODEL 3498
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PALSONIC MODEL 3498 will begin.