User manual ORION TELESCOPES & BINOCULARS DYNAMO INSTUC
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ORION TELESCOPES & BINOCULARS DYNAMO INSTUC. We hope that this ORION TELESCOPES & BINOCULARS DYNAMO INSTUC user guide will be useful to you.
Manual abstract: user guide ORION TELESCOPES & BINOCULARS DYNAMO INSTUC
Detailed instructions for use are in the User's Guide.
[. . . ] The flashlight can be covered with the red filter to preserve night vision under dark skies. To operate the flashlight, the power switch must be in the "ON" position. Press the flashlight button (Figure 1) once to produce a constant light. Pressing the button a second time will cause the flashlight to flash on and off continuously. [. . . ] The green "Ready to Use" LED light will shine when the battery is fully charged. Recharging the Dynamo with DC Current Recharging the Dynamo with DC current should be done with the cigarette lighter receptacle in an automobile. The car's engine must be operating to properly charge the battery. Recharging the Dynamo with DC requires the supplied DC recharging adapter. Press the power switch on the Dynamo into the "CHA" position. Plug the small end of the DC adapter into the charge input jack (Figure 1). Make certain the car engine is running, then plug the other end of the DC adapter into the cigarette lighter receptacle in the car. The red "Charging" LED light will come on indicating that the battery is charging. Charging should take about 5-8 hours the first time you charge the Dynamo. Subsequent charges should only take 6 hours, unless the Dynamo is severely drained. The green "Ready to Use" LED light will shine when the battery is fully charged. Storage and Maintenance
To optimize the lifetime of the Dynamo, several steps should be taken for its proper storage and maintenance. Make certain the power switch is in the "OFF" position before putting the Dynamo in storage. If you are going to store the Dynamo for long periods of time, you should occasionally recharge it (about every three months). Resetting the Circuit Breaker If the power indicator LED light does not come on when you turn on the power switch, the circuit breaker (Figure 1) will need to be reset. Turn the power switch to the "OFF" position and press the circuit breaker button to reset it. Keep in mind that if you are drawing more than 10 Amps through the 12V/10A adapters you will always cause the circuit breaker to break. Replacing the 2-Amp Fuse If the fuse for the 3V/6V/9V power jacks should blow, it can be replaced with a new 2-amp fuse. Turn the fuse-securing knob (Figure 1) in the indicated direction to free the old fuse. Replacing the Flashlight Bulb Should the flashlight bulb break or burn out, it can be replaced with a 12V, . 5A Krypton bulb, available at most hardware stores. Make certain the power switch is in the "OFF" position before replacing the bulb. [. . . ] Spotlight: H3, 12V, 55W Halogen bulb, 800, 000 candlepower, angle adjustable Internal battery: 12V, 7 amp-hour rechargeable sealed leadacid battery Recharging current requirements: 120V, 60Hz AC or 14. 5 to 15. 5V DC Operating temperature: 32° F to 86° F Weight: 8. 4 lbs. Dimensions: 11. 3" x 9. 3" x 5. 2"
Reflector
Remove this clip
Bulb
Bulb
Figure 2. The spotlight reflector dish and bulb.
One-Year Limited Warranty This Dynamo is warranted against defects in materials or workmanship for a period of one year from the date of purchase. This warranty is for the benefit of the original retail purchaser only. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ORION TELESCOPES & BINOCULARS DYNAMO INSTUC
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ORION TELESCOPES & BINOCULARS DYNAMO INSTUC will begin.