User manual OPTEX MORSE GENESYS 824 ALPHA

[. . . ] Then, either select another Quad Key TM or press # to reset the system to it's `Home' Mode. Clear If your Quad Keys control Arming Modes, only one mode may be used at a time. To shift from one mode to another, enter your code to disarm and then re-arm with the mode you desire. If your Quad Keys control Detection Areas, you may select more than one area at a time. To turn off detection appropriate Quad Key TM button and pressing areas, enter your PIN number to turn-off all detection areas. [. . . ] If the `Ready' light is not on, one or more detectors are activating (open) and are not ready to be armed. Depending on your system's design, this may or may not prevent your system from arming. Vision's Zone Indicator lights display which zone(s) have detectors which are in alarm (or open). If you are ub3cle to reset the detectors and return to `Ready' mode, call your security company for assistance. After pressing to begin arming, keypads will beep slowly during the exit delay period (if applicacle). The tempo increases for the last ten seconds of the exit delay period and a sustained tone indicates that the delay period has expired and arming is now complete. After the arming process has been initiated, a valid user PIN must be entered to cancel arming. Additional Arming Options Utility - Arm without entry delay: press - Arm without exit delay: press + + 9 during Exit Delay period. button for - Your entire security system can be turned on by pressing the approximately two seconds. - A PIN number can be required before pressing to turn on the system. Ask your security company if you would like this feature activated. 4 User Functions Vision allows system users to control many advanced features. This provides quick service, greater convenience, and lower operating cost. [1] [2] [3] [4] [5] [6] [7] [8] [9] [0] Chime Smoke Detector Reset System Walk Test Viewing Alarm Memory Viewing System Trouble Bypassing Zones Installer Programming User Programming No Entry Delay Arming/Utility Output No Exit Delay Arming/Quick Exit 11:33am 08/17/05 Chime [1] Chime +1 If your system is equipped, specified detectors can ring a chime tone from the keypads while the system is disarmed. See below for instructions regarding User Programming. [9] No Entry Delay Arming & Utility Output 11:33am 08/17/05 Armed Instant +9 During the exit delay period, enter + 9 to arm your system without entry delays. Anyone entering through a protected door will cause an immediate alarm because the entry delay has been cancelled. This is sometimes used to increase security after everyone has arrived home for the evening. If your system is equipped to operate auxilliary devices, such as an electronic or magnetic door lock, entering + 9 + Utility PIN will activate the device. Ask your security company for additional information about adding or operating this feature. 7 [0] No Exit Delay Arming & Quick Exit 11:33am 08/17/05 Quick Exit +0 During the exit delay period, enter + 0 to arm the system immediately. While your system is armed, press + 0 to bypass the entire system for two minutes. You may enter or exit freely until the system automatically returns to its prior armed status at the end of the two minute period. Press to abort this timer and return the system to its armed state. User Programming System Users with appropriate authority can set User PINs, system time, auto-armimg time, and other advanced features. Only User PINs with authority levels 01 and 02 can access this area. Entering User Programmming + 8 + PIN While the system is disarmed, press + 8 + PIN to enter User Programming. When the system is in User programming's `Home' Mode, the display will scroll through the six User Programming fields: [1] User PIN [2] Temporary PIN [3] Utility PIN [4] Set System Clock [5] AM/PM or 24 Hr. [. . . ] When the system is in User programming's `Home' Mode, the display will scroll through the six User Programming fields: [1] User PIN [2] Temporary PIN [3] Utility PIN [4] Set System Clock [5] AM/PM or 24 Hr. Clock [6] Auto Arm Carefully follow the appropriate programming sequence listed below. If necessary, press # once to return (escape) to the `Home' Mode for User Programming, or twice to return to the system-wide `Home' Mode. Clear [1] User PINs 1+ Press 1 + to enter User PIN Programming. The display requests User Number of the PIN you wish to program [01, 02. . . 08]. [. . . ]