User manual OMNIMOUNT CLMP INSTALL

[. . . ] 25. 25. 1 Note: The elbow joint is pretensioned at the factory and must be adjusted by the Set Screw (25. 1). To lock the arm in position, fully tighten the Set Screw with the smallest (3mm) supplied Hex Wrench. · · · · · · · Thank you for purchasing an OmniMount product. Specifications are subject to change without prior notice. Every effort has been made to provide accurate and error-free assembly and installation. OmniMount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. [. . . ] 6 4 4 6 4 4 6 4 4 4 Tilt--Raising or lowering the screen to improve viewing angle/ picture quality. Fig. 19 Tighten 6 ID A B C D E F G 1/4" Spacers Description Philips screws M4 x 12mm Philips screws M5 x 12mm Philips screws M6 x 12mm Philips screws M4 x 25mm Philips screws M5 x 25mm Philips screws M6 x 25mm Philips screws M4 x 40mm d) b) Adjust Tilt Lever (19. 1) until the display will not move forward without manual adjustment, yet can still be moved with minimal effort. 19) Grasp the upper and lower edges of the display, and then push or pull the display to the desired tilt angle. (Fig 18) To lock the tilt angle, tighten the Tilt Levers (19. 1) securely. 19) For heavier displays, never fully release the Tilt Lever without fully supporting the display. 19. 1 e) The Tilt Lever includes a ratchet function, so that it can be lifted and repositioned for the next turn. To operate the ratchet, pull the lever straight out, rotate it to an unobstructed position, release the lever, and then turn it in the desired direction. 19) H Philips screws M5 x 40mm I J Philips screws M6 x 40mm Philips screws 1/4"-20 x 5/8" Fig. 20 Swivel--Adjust the display for off center viewing positions. Grasp the side edges of the display and then swivel display into desired position. (Fig 20) 2 7 Some displays will require the use of a spacer between the mounting head and the back of the display because the display has a recessed mounting area or a curved back. In this case, use the long screws in pouches G, H or I, along with one or two spacers, as required, (7) for each screw. Step 1 -- Determine the Mounting Location To provide maximum viewing flexibility, the OmniMount Wishbone Series cantilever mounts are capable of a wide range of motion, which allows the display to be positioned for viewing from many different angles. When selecting the mounting location for the display, make sure there is adequate space on all sides of the display, considering the dimensions (H x W) of your particular display model. 9. 1 Secure Mounting Head to back of display using the selected mounting screws (9. 1) and spacers (9. 2) if required. (Fig 9) Caution: NEVER force screws into the display, as damage may occur. 9 Step 2 -- The Installation Template Negative Tilt CAUTION: WHEN REMOVING THE DISPLAY MAKE SURE THE HEAD IS LOCKED IN THE NEGATIVE TILT POSITION, OTHERWISE INJURY COULD OCCUR. The Installation Template is designed to make the installation of the CL-M faster, easier and more accurate. The template also includes a built in dust channel to reduce the clean up chores from mounting the CL-M. Assembling the Dust Channel: Locate the supplied mounting template. Make sure to align the slots on the Mounting Head with flanges on the end of the Mounting Arm. Fig. 1 While holding the display in position, gently pull the bottom of the display forward to create enough space to insert the Clamp Plate ( 10. 1) and Tension Screws (10. 2). (Fig 10) Insert and tighten enough to prevent the screen from moving easily. 10. 2 Using an Adaptor Plate 10. 1 Step 3 -- Mounting to the Wall Follow the instructions based upon your mounting surface: 3a Wooden Stud 3b Concrete/Masonry 3c Cinder Block If your display is not VESA compliant, you will need to use an adaptor plate between your display and the CL--M. Attach the adaptor plate and mount the display as per the adaptor plate instructions. If an adapter plate is required, OmniMount recommends the UA-M or model specific Adapter Plate for the CL-M Step 3a -- Mounting to Wooden Studs The CL-M wall plate can be mounted on a single wooden stud. Step 6 -- Using Cable Management The Wishbone series cantilevers include a cable management function, where cables can be routed along the length of the arm assembly. Using a Phillips Head screwdriver on the Retaining Screw (11. 1) and pushing on the Retaining Nuts (11. 2) with your finger, remove the screw assembly (Fig. 2 Using an electronic stud finder (Fig 2), locate the center of the wooden stud at the desired mounting location. Extend the stud center line, and then draw a horizontal line where you wish the center of the screen to be located. [. . . ] Using a 1/2" (13 mm) drill bit, drill 3 mounting holes 3. 5" (89 mm) deep into the cinder block surface. Note: For best results from the dust channel, press and hold the template against the wall about 2" (50 mm) from where you are drilling. Note: Be sure to hold the guide in an upright position so as not to spill the collected dust. Insert wall anchors into the mounting holes, and lightly tap them flush to the wall with a hammer. [. . . ]