User manual OLYMPUS PT-E06

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual OLYMPUS PT-E06. We hope that this OLYMPUS PT-E06 user guide will be useful to you.


OLYMPUS PT-E06 : Download the complete user guide (1463 Ko)

You may also download the following manuals related to this product:

   OLYMPUS PT-E06 (1487 ko)
   OLYMPUS PT-E06 (1443 ko)
   OLYMPUS PT-E06 (1501 ko)
   OLYMPUS PT-E06 (1517 ko)
   OLYMPUS PT-E06 (1466 ko)
   OLYMPUS PT-E06 (1376 ko)
   OLYMPUS PT-E06 (1503 ko)
   OLYMPUS PT-E06 (1448 ko)
   OLYMPUS PT-E06 (1507 ko)

Manual abstract: user guide OLYMPUS PT-E06

Detailed instructions for use are in the User's Guide.

[. . . ] PT-E06 Jp En Fr De Sp Cs Kr Instruction Manual Underwater Case for digital camera Mode d'emploi Caisson étanche pour l'appareil photo numérique Bedienungsanleitung Unterwassergehäuse für Digitalkamera Manual de instrucciones Caja estanca para la cámara digital Thank you for buying the Underwater Case PT-E06 (hereinafter Case). Please read this instruction manual carefully and use the product safely and correctly. Wrong usage may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. Before use, perform an advance check as described in this manual. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. [. . . ] CAUTION: If the advance test should show water leakage with normal handling, stop using the Case and contact your dealer or an Olympus service station. En EN 10 3. How to connect the electronic flash Connecting the underwater optical fiber cable To connect the UFL-2 underwater flash (optional) to the Case using an underwater optical fiber cable (optional), follow the procedures below. How to connect the underwater optical fiber cable 1 Remove the cap of the optical fiber cable insertion slot. 2 Put the underwater optical fiber cable plug all the way into the optical fiber cable insertion slot. Setting of the digital camera 1 Set the RC mode of the camera to ON so that the camera's built-in flash is activated. 2 Load the camera in the Case with the camera's built-in flash popped up. CAUTION: En When using a non-Olympus manufacturer's slave-type flash with underwater optical fiber cable, set the camera's built-in flash to manual. If the camera's built-in flash ratio is more than 1/64, the camera's built-in flash light may reflect in the lens port and be taken into the picture. EN 11 When using the TTL cable When connecting the optional electronic flash with the underwater TTL cable (optional: PTCB-E01), connect the hot shoe cable (optional: PHCB-01) to the camera and front cover of the Case. Connecting the underwater TTL cable 1 Turn the TTL connector cap of the Case counterclockwise and remove it. 2 Connect the underwater TTL cable (optional: PTCB-E01) to the TTL connector on the Case. Insert into the connector. Underwater TTL cable Use this mark to align the position. 3 When not using the underwater TTL cable, attach the TTL connector cap. Make sure there is no foreign matter attached to the O-rings inside the cap and on the TTL cable connector. After that, gently turn it clockwise until it stops. Check O-rings Turn the threaded section of the connector clockwise gently until it stops. Cap Connector CAUTION: If the TTL connector cap is loose, water leakage may result. How to connect the hot shoe cable 1 Turn the hot shoe cable connector cap inside the Case counter-clockwise to remove it. 2 Insert the connector of the hot shoe cable into the Case's connector and turn the connector screws all the way clockwise to connect them firmly. 3 Load the camera in the Case, and then connect the hot shoe cable to the camera. En EN 12 Setting of the digital camera 1 Set the automatic pop-up setting of the camera to OFF. The camera's built-in flash is designed to pop up automatically when shooting under low light or against the sun in any scene mode other than the AUTO or underwater modes. For details on camera function setup, refer to the camera's instruction manual. When using the electronic flash, be sure to turn it ON before turning the camera on. If the automatic pop-up setting of the camera is ON and the camera is set to the scene mode other than the AUTO or underwater modes, turning the camera ON before turning the electronic flash on would cause the camera's built-in flash to pop up automatically. Always be sure to turn the electronic flash ON before turning the camera ON. CAUTION: · If the camera's built-in flash pops up while the hot shoe cable is connected to the camera, it will interfere with the hot shoe cable, either disconnecting it or causing a connection failure. · When using a slave-type underwater flash from a non-Olympus manufacturer, pop the camera's built-in flash up before loading it in the Case. · Once the Case has been sealed, the built-in flash cannot be popped up or stored. En EN 13 4. Installing the digital camera Check the digital camera Check the digital camera before loading it in the Case. 1. Battery Confirmation Underwater shooting can reduce battery life because the picture has to be checked on the LCD monitor before and after shooting. Make sure that you have sufficient remaining battery capacity before use. 2. [. . . ] · We recommend to perform the check periodically. Maintenance of the threaded sections on the TTL cable and TTL cable connector If the threaded sections used to connect the TTL cable to the TTL cable connector are not maintained properly, salt and other seawater residue may adhere to the TTL cable and prevent it from being disconnected. After use in seawater, clean off any salt, sand, or other residue as soon as possible, then dry the equipment thoroughly. Clean the threaded sections with a cotton swab and apply a thin, uniform layer of silicone grease (provided with this case). Clean and apply silicone grease to these sections. Maintenance of the TTL Connector Cap After removing the TTL connector cap from the Underwater Case, be sure to clean and grease the Oring. Use the maintenance adapter to remove the O-ring unit from the TTL connector cap. TTL connector cap Maintenance adapter En 1 Insert the adapter by aligning its pin with the hole on the cap. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE OLYMPUS PT-E06




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual OLYMPUS PT-E06 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.