User manual MORPHY RICHARDS IB73301

[. . . ] Never pick the cleaner up by the floor nozzle when connected to the mains, use the carrying handle. away from the floor nozzle whenever the cleaner is connected to the mains. Disconnect from the mains supply before attempting to clear blockages, clear the brush or replace the belt. Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance, the plug should be removed and the appropriate one fitted. [. . . ] · Never have the brushes set too low such that the cleaner is hard to push. Floor nozzle height adjustment C Before using the cleaner the floor nozzle height must be set to the correct height. Choose the setting which most closely matches your floor surface, ie deep carpet pile, medium carpet pile, short carpet pile or hard floor. When using the attachments the cleaner must only be used in the upright position with the carpet height adjustment knob set to deep carpet. B min max D Use attachments E C Use DEEP CARPET HARD FLOOR Clean under furniture Flat position 4 8407 Upright ib Comet 5 03/12/2002 1:28 PM Page 5 Using attachments Follow previous steps 1-4 but set the carpet height adjustment knob to the deep carpet setting. 5 Remove the hose connector from the rear of the cleaner and push the required attachment firmly onto the end of the hose. · If additional length is required, attach one or both extension tubes between the hose and tool. IMPORTANT: Never over extend the hose such that the cleaner is pulled over. 4 Take a new dust bag and fold over the top tab at the crease. Holding the cardboard tab, push the bag over the opening of the dirt discharge tube until it is seated against the rear of the enclosure. 5 The front panel will not close unless the dustbag is correctly fitted due to the safety bag interlock. Always check the pre-motor and post motor filters every time you change the dust bag. 6 Once the new dust bag is in place, replace the front panel by aligning the bottom locking tabs with the slots in the body, close cover slowly allowing the front panel to snap in place. The latch will self lock. Dust bag condition When the cleaner is switched on, if the dust bag condition indicator is continuously showing red (or if the suction is reduced) the bag must be replaced and the filters cleaned. If it is still showing red after emptying the dust bag and cleaning the filters, check to see if the hose is blocked. Changing the dust bag F 1 Unplug power cable from wall socket. 3 Remove the old dust bag by holding the cardboard tab and pull towards you. Remove carefully to avoid dust/dirt spilling from dust bag and dispose. F Î 5 8407 Upright ib Comet 5 03/12/2002 1:28 PM Page 6 Changing the filters G Changing the brush belt If the power brush stops rotating it is likely that the drive belt has snapped (usually because the brush has been stalled). Replacement belts can be obtained from Morphy Richards or a Service Agent. 3 Use a cross-head screwdriver to remove the two screws from the front bottom and the central screw under the height adjustment mechanism H. 5 Remove the two screws at the rear and lift the rear of the cover off over the handle release button and unclip the cover from the front of the floor nozzle I. 8 Grasp the brush at both ends and lift straight up J. To maintain suction, the filters must be regularly taken out and cleaned. Failure to clean the filters will reduce the suction and will damage the motor if used for prolonged periods. 2 The pre-motor filter is located underneath the bag and the exhaust filter is below facing forward. [. . . ] For example bags and filters shall have been regularly cleaned or replaced. Morphy Richards shall not be liable to replace or repair the goods under the terms of the Guarantee where: 1 The fault has been caused or is attributable to accidental use, mis-use, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit. 2 The appliance has been used on a voltage supply other than that stamped on the products. 3 Repairs have been attempted by persons other than our service staff (or authorised dealer). 4 Where the appliance has been used for hire purposes or non-domestic use. [. . . ]