User manual MINOURA M70-R

[. . . ] You need to replace the left side coupling (UF-8) with optional "Left Side Coupling for Hub Nut Axle". To use 26x1. 00" or smaller tire, install the supplied Small Wheel Adaptor. · Use the supplied rear quick release skewer for maximum stability. Minoura is not responsible for any problem caused from using your own skewer. [. . . ] Minoura doesn't guarantee the stability if you don't replace the left side coupling. You don't need the supplied quick release skewer if your wheel is a hub nut type. It's not possible to convert your wheel from the hub nut type to the quick release skewer type unless replacing the hub. ! 2. Install the Mag unit and the Roller Pressure Adjust Knob set (MF-3) to the frame. Attach Mag unit to the bracket on frame, align the holes, and put through the bolt. Tighten the bolt with 10mm spanner and M4 hex wrench. ! Do not overtighten the bolt, otherwise the Mag unit will not move smoothly even if you rotate the knob. If properly installed, ` the Mag unit will come down slowly with its own weight when you release it. (Fig. A) Install the knob set to the welded nut on the bracket. ! Make sure the acorn shaped spring direction is as shown in Fig. Failure will cause difficulty on rotating. 3. Fully open both legs and place M70-R/M80-R on a flat and level floor. B) At this moment, make sure all 4 foot are contacting the floor at once to sit on the floor stable. - Page 4 - (Fig. B) 4. Place your rear wheel in between the couplings. 1) Loosen the lock ring (UF-9) to allow the left side coupling (UF-8) be free. C) 2) Pull up the quick hub clamp lever (UF-6) to retract the right side coupling. D) 3) Insert the left side (quick lever side) skewer into the left side coupling first. The quick lever shaft must be inserted into the cut-out on the coupling to hold the bike stable. 4) While keeping this position, slowly come down the bike to align the right side acorn nut to the right side coupling. E) If you start feeling resistance when the lever comes at 4 o'clock position, it's correct. If the clamping hub is too tight or too loose due to wrong position of the left side coupling, pull up the lever to release the bike, adjust the left side coupling position and try clamping the hub again. 6) Lastly, tighten the lock ring to fix the left side coupling position. F) (Fig. F) (Fig. D) (Fig. C) (Fig. E) ! Both left and right side couplings are designed to suit the supplied quick release skewer. The left side coupling must fit perfectly in the skewer head to get correct stability. G) (Fig. G) Any skewer type which lever is located on the end of the axle (Fig. I) cannot be used on M70-R/M80-R. ! Precisely adjust the left side coupling position to keep the correct thightness of rear hub clamping. [. . . ] At this moment, we suggest you to slide the guide pin downward (see the column) to loosen the band for easier work. Decrease 1 2 1 (Fig. O) 3 2 (Fig. P) (Fig. Q) Increase 4. To increase the resistance, twist the lever toward "H". Q) You can choose from 7 different levels to suit your desired workout level. - Page 7 - Why My Remote Shifter Doesn't Work Properly? You may have a shifting problem that you cannot set at L or H position properly due to the lengthened inner cable. To fix this problem, follow the steps to adjust the initial cable tension. 1. Set your remote shifter at "H" position and remove the shifter from your handlebar, then straighten the cable as much as possible. (Fig. R) 2. Pull out the plastic cover cap on foot of the remote cable. R and S) 3. Hold the inside adjusting screw and push it toward the shifter, then adjust the locking nut to set the cable tension properly. [. . . ]