User manual MINOURA E-RDA-850-LW

[. . . ] ! Wipe all oil and moistures out from the rim surface everytime you use the trainer to keep necessary brake performance of your bicycle. -3- HOW TO SETUP YOUR E-RDA850 TRAINER <Required Tools: M5 hex wrench> 1 Open the frame support legs and fit the rubber feet at the correct angle so the base is in full contact with the floor. Do NOT remove the round metal plates from inside the rubber feet when fitting. Ensure the rubber foot caps are facing outwards as incorrect fitting may compromise the stability of the trainer. NOTE: If the both legs don't touch the floor at same time and if one side of the leg is still slightly raised, pull up the leg upward strongly then place the trainer on the floor again. 2 Install the Mag resistance unit on the left side slot and the assistant roller on the right side slot beside the trainer pillar by the supplied M6x12 bolts. B) NOTE: We recommend you to use the reinforcement plate (SR-13) for installing the Mag unit. [. . . ] I) The right side coupling has a black plastic skewer nut protector (called a "Grommet"). This is to protect your skewer from damage during use, however, should you choose to use your own skewer, you should use the supplied grommet to insure a better fit. We will NOT guarantee any fitting problem or accident caused by using your own skewer on the trainer. When you use the supplied skewer, you should remove the grommet from the coupling. I) and then lifting up the grommet. -5- HOW TO INSTALL THE REMOTE LEVER You can install the remote lever on anywhere the diameter is between 22. 2mm (7/8") and 31. 8mm (1-1/4") like as on the handlebar. 1 2 Fully loosen the knob bolt on the plastic holder until it stops then push down the bolt to open the holder. J) Place the holder onto the handlebar, shut the holder, and pull up the bolt then tighten it. K-2) Depends on the diameter of your handlebar, you must adjust the shim as follows; · 22. 2mm (7/8") - 25. 4mm (1"): Install both shims. · 28. 6mm (1-1/8"): Install either right or left side shim. USING THE MAG RESISTANCE UNIT ! When you install the shim on the plastic holder, make sure the direction of the shim as shown in Fig. J-2. The Mag unit has 7 different levels of load force, replicating actual riding resistance. The load settings range from high (H) to low (L) can be adjusted via the white lever on the Magturbo unit or the lever on the thumb shifter type remote lever device. You may also adjust the load force by shifting up or down among your gears, depending on the level desired. We recommend that you start with a medium to low load force and gradually work up, increasing force as your muscles warm up. Increasing Load Force To increase the load force, move the white lever on the Mag unit toward the (H) symbol. L) If your Mag unit is a remote control type, turn the lever on your thumb shifter device toward the (H) symbol. N) Decreasing Load Force To decrease the load force, move the white lever on Mag unit toward the (L) symbol. M) Be sure the lowest selection is not zero load, there still be a small level of force. If your Mag unit is a remote control type, turn the lever on your thumb shifter device toward the (L) symbol. M) ! To make any adjustment to the unit, make sure you are off the bike, and that the trainer has come to a complete stop and that nothing is still moving. (Fig. N) TROUBLE SHOOTING YOUR REMOTE SHIFTER UNIT If you cannot shift to either the lowest (L) or the highest (H) position, it is possible that the inner wire of the remote shifter cable is too long and the wire tension is loose. [. . . ] This work requieres high skill for disassembling and assembling the Mag unit. If you don't have confidence, please ask to the Minoura dealer where you purchased the trainer. The instructions manual will come with the replacement V-belt kit, also you can download it from our web site (http://www. minoura. jp). -7- CHANGING YOUR NON-REMOTE TRAINER TO A REMOTE TRAINER You can change your dial type Mag unit to be a remote controlable one. Of course, the opposite way is possible. 1 Remove the dial lever by removing two small screws. Spring Position for Remote type 2 Remove the bottom spring holder by removing two medium screws and remove the inside spring. [. . . ]