User manual MIMAKI JV5-130S

[. . . ] COLOR INKJET PRINTER OPERATION MANUAL MIMAKI ENGINEERING CO. , LTD. TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan Phone : +81-3-5420-8671 Fax : +81-3-5420-8687 URL : http://www. mimaki. co. jp/ D201515 Foreword Congratulations on your purchase of MIMAKI color ink jet printer "JV5-130S/160S" . The JV5-130S/160S is a color ink-jet printer for high quality printing with solvent ink (4-color and 6color) or water-based ink (4-color and 6-color). How to read this Operation Manual The following documents are attached to JV5-130S/160S: Operation Manual (this document) Explains how to operate JV5-130S/160S. Read this Operation Manual carefully and make the most effective use of your printer. Request for daily care (separate volume) Explains how to perform daily maintenance of JV5-130S/160S. CAUTION DISCLAIMER OF WARRANTY THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR AUTHORIZES DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE ANY OTHER WARRANTY OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH ANY PRODUCT WITHOUT MIMAKI'S PRIOR WRITTEN CONSENT. [. . . ] STEPS: 1 Make sure that the printer is in LOCAL mode. If it is in REMOTE mode, press the [REMOTE] key. L. > [JV5-01] width : mm 2 Press the [ST. MAINT] key and press the [ENTER] key. When [CARRIAGE OUT] is displayed, press the [ENTER] key. Then the carriage moves to above the platen. ST. MAINTENANCE CARRIAGE OUT <ent> 4-7 4 Daily Maintenance 3 Open the right maintenance cover. 4 Pull out the wiper by holding the projections at both ends. 5 Remove the ink from the wiper and the bracket using a cotton swab dampened with the cleaning solution. To replace the wiper, terminate the work instructed here first and then follow the wiper replacement procedure. (See 4-47) 4-8 Cleaning the wiper and ink caps [CARRIAGE OUT] 6 After cleaning the wiper, install it in position by holding the projections at both ends. Be careful of the direction of the wiper. 7 Wipe off ink or dirt adhering to the rubbers of the caps and the wiper cover using a cotton swab dampened with the cleaning solution. Be careful not to leave lint of the cotton swab. Lint may cause printing failure. Ink cap 8 Close the maintenance cover, and press the [ENTER] key. After performing the initial operation, the printer returns to LOCAL mode. Being Initialized :end PLEASE WAIT ST. MAINTENANCE COMPLETED 4-9 4 Daily Maintenance Cleaning the nozzle [NOZZLE WASH] Perform cleaning of the nozzles in the heads to prevent them being clogged with coagulated ink. Be sure to wear the supplied goggle and gloves. The ink contains an organic solvent. If ink settles on your skin or gets in your eyes, immediately and completely wash them off with water. (When solvent ink is used) If nozzle clogging cannot be corrected even after repeating the cleaning procedure described here several times, execute the [FILL UP INK] (Refer to "If nozzles cannot be unclogged [FILL UP INK] (p. 3-31)" ) , [DISCHARGE&WASH] (Refer to "[DISCHARGE&WASH] (p. 5-6)" ) functions. If the remedies instructed here do not work, contact your dealer or an office of MIMAKI. If both of the two cartridges in a set are in [INK NEAR END] or [INK END] status, the nozzle cleaning function (ink suction) is not activated. Replace the cartridges that are in [INK NEAR END] or [INK END] status with ones containing a sufficient amount of ink. STEPS: 1 Make sure that the printer is in LOCAL mode, and then press the [ST. MAINT] key. If it is in REMOTE mode, press the [REMOTE] key. L. > [JV5-01] width : mm ST. MAINTENANCE CARRIAGE OUT <ent> 2 Select [NOZZLE WASH] by pressing the [ The carriage will come out of the capping station. Twice ST. MAINTENANCE NOZZLE WASH ] key twice and press the [ENTER] key. <ent> 3 Open the right maintenance cover. 4-10 Cleaning the nozzle [NOZZLE WASH] 4 Pull out the wiper by holding the projections at both ends. 5 Remove the ink from the wiper, bracket and the vicinity of the wiper insertion hole using a cotton swab dampened with the cleaning solution. To replace the wiper, terminate the work instructed here first and then follow the wiper replacement procedure. (See 4-47) 6 After cleaning the wiper, install it in position by holding the projections at both ends. Be careful of the direction of the wiper. 7 Press the [ENTER] key. Clean a wiper and bracket. WIPER CLEANING COMPLETED(NEXT) : ent 4-11 4 Daily Maintenance 8 Fill the caps with the cleaning solution using a dropper. Ink cap 9 Close the maintenance cover and press the [ENTER] key. Fill a cap with washing liquid fully Fill the liquid. COMPLETED(NEXT) : ent 10Set the time to wait using the [ Normally set 1 minute. ] or [ ] key. Input leaving time. 1 - 99 min ST. MAINTENANCE LEAVING TIME : 1 min Input range: 1 to 99 minutes (In steps of 1 minute) 11Press the [ENTER] key. The carriage returns to the station. The nozzles are capped and the display shown below continues for the set waiting time during which suction of cleaning liquid and cleaning are performed. On the lapse of the set waiting time, the printer performs the initial operation and returns to LOCAL mode. Being Initialized PLEASE WAIT More than 20 seconds remaining During The PostProc PLEASE WAIT ST. MAINTENANCE 01:00 Less than 20 seconds remaining During The PostProc PLEASE WAIT ST. MAINTENANCE ----------- L. > [JV5-01] width : mm 4-12 Cleaning the ink discharge passage [DISWAY WASH] Cleaning the ink discharge passage [DISWAY WASH] Use this function when the [PUMP TUBE WASH] function cannot be used. [. . . ] This icon means using appropriate ones of the [ ], [ ], [ ] and [ ] keys. This icon means pressing the [ ] or [ change the setting value or item. This icon means pressing the [ ] or [ ] key to switch between the alternate sub setting displays or to ] key to switch between setting values or items. This icon means pressing the [ENTER] key once to execute the setting value or item that is currently displayed. ( This icon means pressing the [ST. MAINT] key once. ) This icon means pressing the [END] key to cancel the execution. This graphic represents the display. This graphic shows the behavior of the printer activated as a result of key operation. This graphic shows the set value of a menu item. This graphic shows the message displayed as a result of operation. This graphic shows the work other than the menu operations on the operation panel which you are required to do for the printer. This graphic is used together with the icon . 6-33 6 Operation for Functions Functions related to the cutter When the media is to be cut at a desired position Cut the media at any desired position without using the [AUTO CUT] function. [. . . ]