User manual MCINTOSH MX134

[. . . ] Owner's Manual MX134 A/V Control Center Manufactured under license from Dolby Laboratories, "Dolby", "Pro Logic II", "Pro Logic" and the double-D symbol are registered trademarks of Dolby Laboratories. Surround EX is a jointly developed technology of THX and Dolby Labs, Inc. , and is a trademark of Dolby. Lucasfilm, THX, THX ULTRA, the THX logo, Re-Equalization, Re-EQ, Timbre Matching, Decorrelation, Bass Management, and Loudspeaker Position Time Synchronization are registered trademarks of Lucasfilm, Ltd and manufactured under license from Lucasfilm Ltd. "DTS", "DTS ES", "digital surround", and "coherent acoustics" are registered trademark of DTS Technology, LLC. [. . . ] SYSTEM SETUP Menu will reappear on the Monitor/ Note: The Left Front Loudspeaker Volume Level can serve TV screen and proceed to the next step. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not L o u d s p e a k e r L e v e ls to save them. The MX134 will then return to norL o c a ti o n D e fa u l t S e tti n g N e w S e tti n g mal operation. As the test signal switches to succeeding Loudspeakers, repeat the level adjustment process until the test signal volume levels of all the Loudspeakers are the same. The Loudspeaker level cycling mode can be repeated as often as necessary. Press the SELECT Push-button to switch Off the Automatic Loudspeaker Level Switching Mode. If you do not wish to perform INPUT SETUP Adjustments at this time, select MAIN MENU from the menu. The MAIN SYSTEM SETUP Menu will reappear on the Monitor/TV screen and proceed to the next step. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. Refer to figure 7 on page 23. MENU: SPEAKER LEVEL AUTOMATIC {OFF} MANUAL {ON} LEFT FRONT CENTER RIGHT FRONT RIGHT SURROUND RIGHT BACK SURR LEFT BACK SURR LEFT SURROUND SUBWOOFER MAIN MENU 0 0 0 0 0 0 0 0 Figure 13 L e f t F ron t C e n te r R ig h t F ro n t R ig h t S u rrou n d R ig h t B a c k S urr oun d L e f t B a c k S urro un d L e f t S urr oun d S ubw oof e r 0d B 0d B 0d B 0d B 0d B 0d B 0d B 0d B 29 How to Change the Input Setup The MX134 has eleven Analog Audio Inputs numbered 1 through 11, six Digital Audio Inputs lettered A through F and two Component Video Inputs numbered 1 and 2. These inputs already have assigned titles and associations that will allow for immediate hookup, operation and enjoyment. If these starting assignments and associations do not match up with components in your system, they may be reassigned from the default settings. The following example will illustrate how to rename the AUX Input to DVD2 and assign it a Digital Input. When the Zone A or B Input Selector is rotated to select what was originally the AUX Input, DVD2 will now appear on the Front Panel Alphanumeric Display. The Video Power Control, Video Converter and Component Video can also be set for each Input. Notes: 1. The Source Input Number 0 will always be assigned to the Tuner Input and can not be reassigned. Unused Inputs may be switched Off so that they will not appear when rotating through the input source choices using the Zone A or Zone B Input Selector and also will not be available when using the Remote Control or Keypad. Each Analog Audio/Video Input must have a unique title (type and number) assigned to it. Example, there can not be a DVD3 Input without first having DVD1 and DVD2 inputs. MENU: INPUT SETUP SOURCE INPUT TITLE DIGITAL INPUT VIDEO POWER COMPONENT VIDEO VIDEO CONVERTER IN MAIN MENU 1 AUX NONE ON NO OFF Figure 14 1. Press and hold the Front Panel SETUP Push-button approximately three seconds to enter the Setup Mode. The word SETUP will appear on the MX134 Front Panel Display and the MAIN SYSTEM SETUP Menu will appear on the Monitor/TV screen. Using the Up or Down directional push-buttons on the Remote Control, select Input Setup on the OnScreen Menu, followed by the SELECT Push-button. [. . . ] To verify the Station Preset(s) just entered into memory, press the PRESET Left and Right Pushbuttons to cycle through and confirm your preset assignments. Note: Pressing the REVIEW Push-button on the Remote Control will also allow reviewing the stored Presets. Figure 80 1. Press the Front Panel TUNING Up or Down Pushbutton, or the CHANNEL Up or Down Push-button on the Remote Control, to select a station. The Front Panel Alphanumeric Display will indicate 1 AVAILABLE, which is the first of 9 Preset Numbers that can be assigned. The Station that is about to be entered into memory may also assigned to a different Preset Number (2-9) by pressing the PRESET Left and Right Push-buttons to select the desired Preset Number. Note: Presets are automatically assigned in order from 1 to 9 unless a different Preset Number is selected How To Clear an Assigned Station Preset 1. [. . . ]