User manual MATSONIC MS5025
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MATSONIC MS5025. We hope that this MATSONIC MS5025 user guide will be useful to you.
Manual abstract: user guide MATSONIC MS5025
Detailed instructions for use are in the User's Guide.
[. . . ] The information presented in this publication has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. Specifications are subject to change without notice.
Trademarks
IBM, PC/AT, and PC/XT are trademarks of International Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
AMD is a trademark of Advanced Micro Devices Inc.
Cyrix is a trademark of Cyrix Corporation.
IDT is a trademark of Integrated Devices Technology Corporation.
AMI is a trademark of American Megatrends Inc.
MS-DOS and WINDOWS NT are registered trademarks of Microsoft Corporation.
ii
Contents
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 2: Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Two of which are black, orient the connectors so that the black wires are in the middle. Pin 1 2 3 4 5 6 Description Power Good +5V DC +12V DC 12V DC Ground Ground Pin 7 8 9 10 11 12 Description Ground Ground 5V DC +5V DC +5V DC +5V DC
8
Chapter 2
PWR2 ATX Power Connector
The ATX power supply provides a single 20-pin connector and supports the ACPI specification. Pin 1 2 3 4 5 6 7 8 9 10 Description 3. 3V 3. 3V Ground +5V Ground +5V Ground Power OK 5VSB +12V Pin 11 12 13 14 15 16 17 18 19 20 Description 3. 3V 12V Ground PS-ON Ground Ground Ground 5V +5V +5V
Software Power-Off
Follow the steps below to use the Software Power-Off Control function in Windows 95 with ATX power supply. will not be shown when using this function.
Hardware Configuration
9
COM1/2 Serial Port #1/#2 PRN Parallel Port FDC Floppy Disk Port IDE1/IDE2 Primary/Secondary IDE Ports KBD Keyboard Connector J2 ATX FORM CARD Connector:
(1-4, 10-13) 2 sets of Universal Serial Bus (USB) Pin 1 2 3 4 Description +5 VDC Data Data + Ground Pin 10 11 12 13 Description +5 VDC Data Data + Ground
(5-6, 15-16) PS/2 Mouse Pin 5 6 15 16 Description +5 VDC Mouse CLK Mouse Data Ground
(7-9, 17-18) Infrared Pin 7 8 9 17 18 Description Ground IR Hi +5 VDC IR In IR Out
10
Chapter 2
J11 (2, 4, 6, 8, 10) (KEY LOCK) Keylock & Power LED Connector
Pin 2 4 6 8 10 Description LED Output N. C. Ground Keylock Ground
J11 (1, 3, 5, 7) (SPK) Speaker Connector
Pin 1 3 5 7 Description Data Out N. C. Ground +5V
J11 (13, 14) (TB-LED) Suspend LED Connector
Pin 13 (+) 14 () Description +5V Active Low
J11 (15, 16) (HDD-LED) HDD LED Connector
Pin + Description +5V Active Low
Hardware Configuration
11
J11 (17, 18) (RST) Reset Switch Connector
Setting Open Close Description Normal Mode Reset System
J5 (CPU-FAN) Fan Power Connector
Pin 1 2 3 Description N. C. +12V Ground
JP6 (PWR-BT) Over Ride Power Button Connector
Attach the ATX Power Button or Suspend Switch cable to this connector. In the AT power system, this connector will act as a suspend switch; and in the ATX power system, this connector will be not only an ATX power button but a suspend switch as well. Details are described below: When the system is off, push the power button to turn the system on. When the system is on, push the power button rapidly to switch the system to the Suspend mode, and, by pushing and holding the button for more than 4 seconds to turn the system completely off. When the system is in the Suspend mode, push the power button rapidly to turn the system on.
12
Chapter 2
JP1 (WOL) Wake On LAN Connector
While in Soft-off/Suspend state, if an external LAN signal occurs, the system wakes up and can be accessed with the LAN card. Pin 1 2 3 Description 5V Stand By Ground Active Low
Jumper Settings
J1 CMOS RAM Discharge Selector
Setting Normal Mode Clear CMOS Description
1
1
JP2 DIMM Voltage Selectors
Voltage 5V 3. 3V Settings
1 3
1
3
Hardware Configuration
13
Memory Installation
The mainboard lets you add up to 256MB of system memory through SIMM and DIMM sockets on the board. Four SIMM sockets on the mainboard are divided into two banks: Bank 1 and Bank 2. When Hit <DEL> if you want to run SETUP appears, press the <DEL> key to enter the BIOS setup program. The following screen appears:
AMIBIOS Setup, Version - 2. 4 (C) 1997, American Megatrends Inc. Security
2.
American Megatrends Setup
Standard
Advanced
Chipset
User CPU
Anti-Virus
PCI
Power Mgmt PCI/PnP Peripheral Utility
CPU PnP Default
Detect IDE
Original
Optimal
Best
Set Date, Time, Floppy, Hard Disk
Alt+H: Help
3.
Use your keyboard or mouse to choose options. Press Alt-H for Help.
16
Chapter 3
Default
Every option in BIOS Setup contains three default values: Original default, Best default, and the Optimal default value. Original: The original default values recover the modified settings to the original values. Optimal: The Optimal default values provide optimum system settings for all devices and system features. Best: The Best default values provide best performance settings for all devices and system features, but dependent used devices and we arent guaranty that system run overnight on these settings.
Setup Window
The Setup section has six icons that allow you to set system configuration options.
Setup
Standard
Advanced
Chipset
PCI
Power Mgmt PCI/PnP Peripheral
BIOS Setup
17
Standard Setup
Choose the Standard icon from the Setup section on the BIOS Setup main menu. Pri Master Pri Slave Sec Master Sec Slave Choose these icons to configure the hard disk drive named in the option. When you click on an icon, the following parameters are listed: Type, LBA/Large Mode, Block Mode, 32Bit Mode, and PIO Mode. [. . . ] The system enters the full power on state if any activity occurs.
RTC Alarm Set this option to enable the RTC Alarm to Resume From Soft wake up the system which is Soft Off. Off RTC Alarm Date; Set these options to specify the RTC Alarm RTC Alarm Hour; time on Date/Hour/Minute/Second. RTC Alarm Minute; RTC Alarm Second
BIOS Setup
23
PCI/PnP Setup
Choose the PCI/PnP icon from the Setup section on the BIOS Setup main menu. Plug and Play Aware OS Set this option to Yes if the operation system in this computer is aware of and follows the Plug and Play specification. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MATSONIC MS5025
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MATSONIC MS5025 will begin.