User manual LA CROSSE TECHNOLOGY WS9124ITCA

[. . . ] After inserting the battery into the sensor, the Temperature Station will start receiving data from the sensor. The outdoor temperature and the signal reception icon should then be displayed on the Temperature Station. If this does not happen after 3 minutes, the batteries will need to be removed from both units and reset from step 1. In order to ensure sufficient 915 MHz transmission there should be a distance of no more than 330 feet (100 meters) between the final position of the Temperature Station and the sensor (see notes on "Mounting" and "915 MHz Reception"). [. . . ] Return used batteries to an authorized depot. FUNCTION KEYS: Temperature Station: The Temperature Station has two easy to use function keys. SET/ CH key MIN/ MAX/ + key 6 SET/CH key (Setting/Channel) · Press and hold for approximately 3 seconds to enter the Manual setting mode. · Press and release to toggle between different channel readings. MIN/MAX/+ key (Min/ Max temperature) Used to toggle between the minimum and maximum recorded readings of indoor & outdoor temperature and indoor humidity. · Press and hold to reset minimum and maximum record (when min or max record is shown). · LCD SCREEN AND SETTINGS: Time Indoor Temperature in °F or °C Channel No. Outdoor Temperature in °F or °C Sensor Low battery indicator Indoor Humidity %RH Outdoor Reception Signal icon* Receiver Low * battery indicator When the signal from the sensor is successfully received by the Temperature Station, this icon will be switched on. User can therefore easily see whether the last reception was successful ("ON" icon) or not 7 ("OFF" icon). On the other hand, the short blinking of the icon shows that a reception is being done at that time. For a better display clarity, the LCD screen is split into 3 sections, showing the information of time, indoor temperature and humidity, and outdoor data. Section 1 - TIME · Display of time (manually set). · Section 2 - INDOOR TEMPERATURE AND HUMIDITY Display of indoor temperature and humidity. Section 3 - OUTDOOR TEMPERATURE · Display of the outdoor temperature. MANUAL SETTING: 12 / 24- HOUR TIME DISPLAY SETTING AND TEMPERATURE UNIT (°C/°F) SETTING User may choose to display the time in 12-hour or 24-hour mode: Note: When the time display is set as 12-hour mode, the temperature unit will be fixed to °F; when the time mode is in 24-hour format, the temperature unit will be set to °C. In normal display mode, press and hold the "SET/ CH" key for approximately 3 seconds. Press the "MIN/MAX/+" key to set the desired time display mode. Press and release the "SET/ CH" key to confirm and advance to the MANUAL TIME SETTING. 8 MANUAL TIME SETTING User shall manually set the time of the Temperature Station by the following steps: 1. Press the "MIN/MAX/+" key to adjust the hour (press and hold to allow fast advance). Press "SET/ CH" key to confirm and go to the minute setting. Press the "MIN/MAX/+" key to adjust the minute (press and hold to allow fast advance). Press "SET/ CH" key once more to return to normal display. VIEWING THE MINIMUM AND MAXIMUM READINGS: User may consult the minimum and maximum recordings for indoor temperature and humidity, and outdoor temperature by following these steps: 1. Press the "MIN/MAX/+" key once to view the minimum indoor temperature and humidity and minimum outdoor temperature. Minimum icon 2. Press the "MIN/MAX/+" key once more to view the maximum indoor temperature and humidity and maximum outdoor temperature. 9 Maximum icon RESETTING THE MINIMUM AND MAXIMUM READINGS: User may reset the minimum and maximum temperature / humidity data to the current value by the following steps: 1. Press and hold the "min/max/+" key for about 3 seconds to reset all the minimum / maximum data to the current values in a single action. (Data of all outdoor and indoor data will be reset at the same time. ) TEMPERATURE SENSOR: The outdoor temperature is measured and transmitted to the Temperature Station every 16 seconds approximately. The range of the temperature sensor may be affected by the temperature. Please keep this in mind when placing the sensor. 915 MHz RECEPTION CHECK The Temperature Station should receive the outdoor temperature data within a few minutes after setup. If the temperature data are not 10 received about 2 minutes after setup (the signal reception icon does not appear), please check the following points: 1. [. . . ] Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner's manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. . This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. [. . . ]