User manual LA CROSSE TECHNOLOGY TX22U-IT

[. . . ] Once the batteries are installed, all segments of the LCD will light up briefly and a short signal tone will be heard. It will then display the time as 12:00, the date as 1. 1. 05, the weather icons, and air pressure value. Afterwards, the Weather Station will start receiving data from the transmitter. The outdoor temperature, humidity wind chill and wind speed should then be displayed on the Weather Station. [. . . ] The first wall will reduce the range to 165 feet, and the second wall will reduce the range to 87 feet. Factoring in the 10 foot room, this leaves a maximum of 77 feet of remaining signal range. This allowance is typically enough for a frame wall with nonmetallic siding; however certain materials can reduce range even further. Metal siding, stucco, and some types of glass can reduce signal range by as much as ¾ or more, compared to the ½ reduction typical of most obstructions. It is possible to receive a signal through these materials, however maximum range will be much less due to their tendency to absorb or reflect a much larger portion of the sensor's signal. · The Thermo-hygro transmitter transmits a signal about every 4. 5 seconds. After the batteries have been installed, the indoor weather station will search for the signal for the duration of few minutes. If there is no temperature or humidity reading in the OUTDOOR LCD or wind speed in the WIND SPEED LCD after 5 minutes, user shall make sure the units are within range of each other, or repeat the battery installation procedure. If a button is pressed before the indoor weather station receives the signal from the Thermo-hygro transmitter, you will need to follow the battery installation procedure again. Note: · · After batteries are installed in transmitter, user shall also power up the Weather station to receive the signal from the transmitter as soon as possible. If the weather station is powered after more than 5 hours the transmitter is powered, the weather station will never receive signal successfully from this transmitter. In this case, user will need to reinstall the batteries from the transmitter to redo setting-up procedures. Detailed Set up procedures of the Weather Station, the Relay Transmitter, the Rain sensor and the Wind Sensor refer to the main operation manual of WS- 1610. · MOUNTING THE THERMO-HYGRO TRANSMITTER The Thermo-hygro transmitter can be mounted in several ways: · With the use of screws · Using adhesive tape (Use Tape as a positioning tool only. ) · Using nylon straps SETTING UP Wireless transmission at 915 MHz - thermohygro transmitter to weather station MOUNTING WITH SCREWS Weather Rain Wind Cable connection Cable connection between between the rain the wind sensor and the thermo-hygro transmitter sensor and the thermo-hygro transmitter 1 1) 2) 3) 4) 5) Remove the mounting bracket from the Thermo-hygro transmitter . Through the two screw holes of the bracket, mark the mounting surface with a pencil. Insert the Thermo-hygro transmitter into the bracket. determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. [. . . ] · Immediately remove all low powered batteries to avoid leakage and damage. Contact La Crosse Technology for repairs. SPECIFICATIONS Note: Detailed Set up procedures of the Weather Station, the Relay Transmitter, the Rain sensor and the Wind Sensor refer to the main operation manual of WS-1610. Weather data measuring range: Outdoor and dew -40°F to +140°F with 0. 2°F resolution (point: 40°C to 59. 9°C with 0. 1°C resolution) "OFL" displayed if outside this range Outdoor relative 1% to 99% with 1% resolution ("- - " humidity measuring displayed if < 1%; "99" displayed if range: 99%) Transmission range: 330 feet (in open space) Power Supply: Thermo-hygro 2 x AA, IEC LR6, 1. 5V transmitter : Battery life cycle: Approximately 12 months Recommended Alkaline battery type: Dimensions (H x W x D): Thermo-hygro 2. 25" x 2. 44" x 6. 18" transmitter (57. 3 x 62 x 157 mm) WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. [. . . ]