User manual KOMPERNASS POWERFIX KH 4179 LASER SPIRIT LEVEL

[. . . ] NEVER direct the laser beam at people or animals. NEVER look directly into the laser beam. · Do NOT direct the laser beam at strongly reflective materials, for example, mirrors. · Exercise particular caution if you wear contact lenses or spectacles or are using a light-bundling device such as a magnifiying glass. [. . . ] · Should a battery be accidentally swallowed, IMMEDIATELY seek medical assistance! Items supplied 1 x Laser Spirit Level 1 x Tripod-Stand 2 x 1. 5 V Batteries Type AAA/Micro 1 x Operating instructions Description of the appliance q Spirit level for vertical measurements w Spirit level for horizontal measurements e On/Off switch for spirit level illumination r On/Off switch for laser beam t Laser beam exit opening y Measurement scale u Ball and socket joint with retaining screw i Tripod-Stand with telesopic legs o 2 Retaining magnets integrated in the housing a Batteries s Battery compartment screw fixings -4- Technical Data Spirit level: 2 integrated bubble glasses, illuminated Power supply: 2 x 1. 5 V Type AAA/Micro Laser class: 2 Max. output power (P. max): < 1 mW Wave length (): 650 nm according EN60825-1:2007 Unpacking · Check that all items listed are available and that they show no signs of visible damage. · Remove all parts from the packaging and all packaging remnants from the items. · Retain the packaging, either for storing the appliance or for reuse in the event of posting it to Customer Services for repair. Inserting the batteries · Remove the battery compartment screws s and insert the two batteries a 1. 5 V Type AAA/Micro as shown in the illustration. The appliance is now ready for use. -5- Placement · Two retaining magnets o have been integrated on the underside of the laser spirit level to secure the appliance onto steel surfaces. · If you wish to use the tripod-stand i, screw these firmly onto the appliance underside. · Align the laser spirit level at its desired location so that, in the two spirit levels q and w, the air bubbles lie precisely between their respective markings, the laser spirit level is then positioned exactly level in all directions. A ball and socket joint with retaining screw u is available for this on the tripod stand. To level out floor/ground irregularities, the telesopic legs i on the tripod stand can be drawn out to varying lengths. Utilisation Attention!! This appliance contains a Class 2 laser. NEVER direct the laser beam at people or animals. NEVER look directly into the laser beam. · Press the On/Off switch r for the laser. When the appliance is correctly aligned in all directions, as described on Page 6, there now appears a red laser line r on the wall it is directed at, a line which is level with the floor/ ground. If the laser spirit level is standing on a level floor/the ground without the tripod stand, the vertical distance of the laser line from the base level amounts to 29, 5 mm. In darkened light conditions the spirit levels q and w now glow lightly. · For simple length measurements a measuring scale y is printed onto the side of the laser spirit level. -6- Cleaning and Maintenance To avoid the risk of eye damage: · Remove the batteries before cleaning the appliance. This will prevent the laser beam from being accidently switched on during cleaning. Cleaning the appliance: · Clean the appliance parts only with a dry or lightly moistened cloth. To avoid damage to the upper surfaces, do not use abrasive or aggressive cleaning agents. · If soiling is visible in the laser beam exit opening t, this should be carefully removed with a cotton stick. Maintenance · NEVER open any of the parts of the appliance. No form of maintenance, either on or in the appliance, is intended for execution by the user. [. . . ] · , . : · ( ) , / , . · / , ! 1 x 1 x 2 x 1, 5 V AAA/Micro 1 x q w e / r / t y u i o 2 a s - 12 - : : : . (P. max): (): 2 , 2 x 1, 5 V AAA/Micro 2 < 1 mW 650 nm EN60825-1:2007 · , . [. . . ]