User manual KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW. We hope that this KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW user guide will be useful to you.


KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW : Download the complete user guide (936 Ko)

Manual abstract: user guide KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW

Detailed instructions for use are in the User's Guide.

[. . . ] Always keep the power cable well out of the jigsaw's working area and fed to the rear of the machine. 4 If you are working for long periods on wood or materials which give rise to dangerous dusts, fit the jigsaw with a suitable tested vacuum extraction device. Do not drill into the jigsaw's housing as that will break the protective insulation (Use stick-on labels, plates etc. ). Cracked or deformed saw blades are not to be used. INSTALLING THE SAWBLADE Push the saw blade shaft as far as the stop into the blade holder. Take the Allan key (from its holder in the case) and tighten both bolts. [. . . ] Material Rubber Aluminium Steel Wood Speed 1-3 4-5 4-5 6 SETTING THE PENDULUM ACTION Use the following advisory settings as a guide (for reference only) to the pendulum action settings and choose an appropriate pendulum setting on the pendulum action control º for the material to be sawn. Setting the pendulum action increases or reduces the penetrating effect of the saw blade into the material. The following rules of thumb apply: Soft material = large pendulum action Hard material = small or no pendulum action Clean cut edge = no pendulum action Material Rubber Aluminium Steel Wood Plastic Ceramic Pendulum Setting 0 0-1 0 1-3 1 0 Note: the pendulum action setting on the pendulum action control º can be altered whilst the machine is operating. PLUNGING CUTS Plunging (interior cutting or plunge sawing) is only possible in softer materials such as for example wood or light-weight building materials. For harder materials you must insert the saw blade into a suitably sized hole in the material to be sawn. Set the base plate ² (see "Setting the base plate") into the rearmost position so that a good angle for plunging is achieved. Set the pendulum action on the pendulum control º to "0" 2. With the machine switched off, place it with the front edge of the base plate ² at the cutting position. Switch the machine on and plunge the oscillating saw carefully into the material. USE OF THE PARALLEL GUIDE The PPHSS 670 pendulum action jigsaw is equipped with a parallel guide µ. Slide the parallel guide in from the appropriate side, the left or right accordingly. Make sure that the guide surface of the parallel guide points downwards. 6 VACUUM CHIP EXTRACTOR Caution!: Only use the equipment with a compatible vacuum chip extractor. The vacuum chip extraction nozzle » has a standard internal diameter of 35 mm. Connect a household vacuum cleaner or a wet and dry vacuum cleaner to the nozzle as follows: 1. Rotate the vacuum hose on to the extraction nozzle and test whether it is securely held in place. Slide the clear-view cover ´ downwards for optimum chip extraction. MAINTENANCE OF THE JIGSAW 1. For the best results do this straight after the work has been completed. Air vents must always be clear and clean. ADVICE ON WORKING METHODS, TIPS AND TRICKS Here is some advice on adjustment of the clear-view cover ´ to give you optimum chip extraction: the chip blower blows the chips away from the cut. The distribution of vibration makes operation smoother because of weights moving in opposite directions on the foot. The base plate ² can be set at an angle of up to 45° in both directions. For plunging cuts and sawing near an edge, the base plate can be set towards the rear. Here is some advice on the pendulum action control º: the saw blade is only pressed against the material on the return stroke / working stroke. [. . . ] The PPHSS 670 pendulum action jigsaw is equipped with INTELLIGENT POWER CONTROL This automatic power control ensures that within a certain oscillation range the output from the jigsaw remains constant even when cutting harder and more resistant materials. Further practical tips for power tools can be found in the accompanying booklet on safety advice. We reserve the right to make technical modifications in the course of further development. 7 WARRANTY This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase (if available) to the closest service address. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KOMPERNASS PARKSIDE PPHSS 670 PENDULUM ACTION JIGSAW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.