User manual KENWOOD TS-530SP

[. . . ] This transceiver features a Digital Signal Processing (DSP) unit to process IF and AF signals. By taking maximum advantage of DSP technology, the TS-530SP transceiver gives you enhanced interference reduction capabilities and improves the quality of audio. As you learn how to use this transceiver, you will also find that Kenwood is pursuing "user friendliness". in Menu mode, you will see scrolling messages on the display, telling you what you are selecting. [. . . ] This is because the frequency on the display always shows the true carrier frequency for all modes. If you want the transceiver to shift the reception frequency to trace the receiving CW signal when changing the mode from SSB (USB or LSB) to CW, switch this function ON. The transceiver shifts the reception frequency when changing the mode from SSB to CW, so you can still hear the target signal and instantly transmit the signal in CW without adjusting the frequency. 1 Press [MENU], then press [Q-M. IN]/ [Q-MR] or turn the MULTI/CH control to select Menu No. 3 Press [MENU] to exit Menu mode. 35 If you operate both SSB and CW modes, you can configure the transceiver to change the operating mode from SSB (USB or LSB) to CW and then transmit in CW mode automatically when you operate the CW keyers. The mode automatically changes from USB to CW and LSB to CWR, regardless of the setting for Menu No. Therefore, when the CW signal is received in SSB mode, you can operate the paddle or keyer to immediately communicate CW with another station. 1 Press [MENU], then press [Q-M. IN]/ [Q-MR] or turn the MULTI/CH control to access Menu No. 3 Press [MENU] to exit Menu mode. Note: You must switch the CW Break-in function ON to change the mode and transmit in CW mode {page 32}. This function allows you to send CW messages without using an optional paddle {page 2}. The Mic [UP] key can be used as the dot paddle and the Mic [DWN] key can be used as the dash paddle. To activate Mic UP/ DWN key Paddle mode: 1 Press [MENU], then press [Q-M. IN]/ [Q-MR] or turn the MULTI/CH control to access Menu No. Using the sound function of your PC along with PSK31 software, many amateur radio operators enjoy PSK31. · When managing PSK31 using the sound capability of a PC, use SSB mode. · Refer to "EXTERNAL AUDIO SETTINGS" {page 58} for Audio Settings. For further information, consult reference books about Amateur Radio. · If necessary, access Menu No. The audio output level of ANO (ACC2 connector/ pin 3) changes {page 65}. The AF control cannot be used to adjust the audio level for your MCP. 6 Some stations may be operating in Reverse shift. In this case, press and hold [CW/FSK (REV)] to reverse the shift (the upper sideband is used). · "FSR" appears. · Traditionally, the lower sideband is used for FSK operation. "FSK" appears. 7 Follow the instructions provided with your MCP and enter a command from your computer to transmit. 37 Kenwood digital signal processing (DSP) technology is adapted to this transceiver. Using DSP filtering (AF), you can control the bandwidth, cancel the multiple jamming beat, and reduce the noise level. 1 Select CW or FSK mode. [. . . ] · A confirmation message appears when performing the VFO Reset. Otherwise, press any other key to cancel the VFO Reset and return to normal operation. · The VFOs reset to the factory default values. For each VFO, the factory defaults for the operating frequency and mode are as follows: · VFO A: 14. 000. 00 MHz/ USB · VFO B: 14. 000. 00 MHz/ USB The Memory channels and Quick Memory channels have no data stored. Perform a Full Reset if you want to erase all the data in all the memory channels. In addition, this function resets all the settings that you customized, to the factory defaults (i. e. - menu settings, antenna tuner preset data, etc. ). [. . . ]