Detailed instructions for use are in the User's Guide.
[. . . ] Using the navigation system for a long time with the engine switched off can cause the battery to run down.
Time before current position is displayed
The mobile navigation system will not display the correct current position of the vehicle the first time it is used after purchase, or if the battery has been removed for a long time. GPS positioning signals will soon be received, however, and the correct position will be displayed.
OBSERVE LOCAL TRAFFIC SIGNS AND REGULATIONS
Always observe the local traffic signs and regulations whilst driving and check them against the system's instructions. Due to frequent changes in local signs and regulations, the traffic sign and regulation data on the Map DVD-ROM may be outdated. Furthermore the Map DVD-ROM cannot reckon with certain conditions such as traffic density at certain times of the day, (temporary) road closures due to construction work, weather conditions or special events taking place. [. . . ] · Repeat step 1 and 3 until all desired way points have been set.
Modification of Destination or Way Point Positions
This function allows the calculated route will be displayed and the positions of the destination or way points to be modified.
Before Steps
3
(Route Options) 3
(Dest. (Change Location).
3 4
Select the button for the location to be modified.
The map for the area around your current location will be displayed.
Move
to location and then select
.
5
Select
.
Modification of the Visiting Order
The order in which way points are to be visited can be modified using this function.
Before Steps
3
(Route Options) 3
(Dest. & Way Pt. )
1 2
Select
.
Select the buttons for the way points in the order that they should be visited.
If you wish to cancel an indication, select .
3
When the sequence has been completed, the visiting order will be updated automatically.
4 5
Select Select
. .
English 27
Route Options
English
Deletion of Destination or Way Points
The destination or any way point which has been set may be deleted using this function.
Before Steps
3
(Route Options) 3
(Dest. & Way Pt. )
1 2
Select
.
Select the button corresponding to the destination or way point to be deleted.
3
Select displayed.
Select
when the confirmation message is
to cancel the deletion.
4
Select
.
Deletion of Destination and All Way Points
The destination and all way points which have been set may be deleted using this function.
Before Steps
3
(Route Options) 3
(Dest. when the confirmation message is
to cancel the deletion.
28 English
Display Route
Use this function to display the entire calculated route.
Before Steps
3
(Route Options) 3
(Display route)
1
Select
.
The Entire Route screen appears.
:
You can set any areas you want to avoid from the list of street names. : Recalculates the route.
If the data for the route cannot be shown on one screen, you can scroll using and .
2
Route Preview
Select
.
The mobile navigation system can show you an automated simulation of the calculated route.
Before Steps
3
(Route Options) 3
(Route Preview)
1
Use the buttons displayed onscreen to carry out a simulation run.
: Move to the start point. When the run has been started, this button will be displayed as , and when selected, it will cause running to take place at high speed. When the run has been started, this button will be displayed as , and when selected, it will cause running to take place at high speed. : Displays the EDIT ROUTE PREVIEW screen (see page 30).
The speed of the simulation run can be altered by changing the scale of the map. The simulation run is faster with a wider area map and slower with a closer up map.
English 29
Route Options
English
Setting the conditions for simulation run
Before Steps
3
(Route Options) 3
(Route Preview)
1
Select
.
EDIT ROUTE PREVIEW screen appears. You can also change the viewing angle of the 3D display.
Before Steps
3
(Navigation Set Up) 3
(2D/3D View)
1
Select a 2D or 3D display for the Map Screen and the Guidance Screen.
Map Screen: Changes the map screen display. Guidance Screen: Changes the route guidance screen, such as the enlarged junction diagrams.
2
Select
or
on the angle indicator.
In situations where 3D is selected on the Map screen, it will be possible to modify the map angle. The view point will be higher up when closer to , and lower down when closer to . : Restores the initial default angle setting.
To implement 3D display on the right side of a dual map, touch the top of the right-hand screen and then select .
34 English
Calibration
This function allows you to correct any error in the position or direction of your vehicle display.
Adjusting Current Position and Direction
Before Steps
3
(Navigation Set Up) 3
(Calibration)
1
Select
.
2
Move
to the correct position and select
.
3
Use or to adjust direction in which you are heading, and select .
Distance
This function automatically corrects any error in the display of the current position that might occur after tyre replacement.
Before Steps
3
(Navigation Set Up) 3
(Calibration)
1
Select
.
You will have to drive about 6 miles (10km) before distance correction is complete.
English 35
Navigation Set Up
English Navigation Information
Vehicle Signal
This function allows vehicle and GPS satellite data to be displayed.
Before Steps
3
(Navigation Set Up) 3
(Navigation Information)
1
Select
(Vehicle Signal).
VEHICLE SIGNAL screen appears.
Map Version
This function enables you to check the version of the map disc you are currently using.
Before Steps
3
(Navigation Set Up) 3
(Navigation Information)
1
Select
(Version).
The version of the map disc and TMC tuner you are using now is shown.
36 English
Set Clock
The current time is set using this function. Since time notification is provided by a GPS satellite, time-zone adjustment can be carried out automatically.
Before Steps
3
(Navigation Set Up) 3
(Set Clock)
1
Select
if you would prefer 24-hour display; for 12-hour display.
2
Restore System Defaults
Select to move the setting ahead by one hour, and similarly, select to move it back by one hour.
This function replaces all the settings in the mobile navigation system with the initial default settings.
Before Steps
3
(Navigation Set Up) 3
(Restore System Defaults)
1
Select
.
: Restores the average speed setting to the initial value upon factory setting.
IMPORTANT If you execute Restore System Defaults, all of your Stored setting data will be deleted.
[Default List]
Item Map display Search Area Display Guidance Language Map Orientation (1 and 2 screen) Map Display Mode Map Display Scale Initial condition B (Belgium) UK English North up 2D, single-screen display Single-screen: 10, 000 map (1/16 min) (100 m) Dual-screen: 40, 000 map (1/4 min) (500 m) Arrow Mode Off Off Auto On Off Next passage point Item Navigation Setup Menu Distance Road Restriction Warnings Audio Mute Keyboard Layout Arrival Time Colour Scheme Guidance Screen Q-POI Selection Initial condition km On On ABC Estimated arrival-time display 1 On A : Petrol B : Parking C : All Restaurant D : Hotel E : Hospital F : Golf Cource 4 2D (Map/Guidance Screen) 23° 24h Short Cut 1: Detour Short Cut 2: Map Direction Quick Allow Motorway :On Allow Toll Road: Off Allow Ferry: Off Allow Restricted Road: Off Allow Seasonal Restricted Road: Off Allow Car Train: On On Off On Auto - Germany
Map Configuration Q-POI Map Display Show POI Icon Display Map Mode Right Screen Setting, POI Right Screen Setting, 3D Passage Point Display/ Current Location, Map Screen (Time Requirement, Time, Direction/Distance) Passage Point Display/ Full Route, Map Screen (Time Requirement, Time, Direction/Distance) On-Route Scroll Setting Mode On-Route Scroll Display Items Motorway information Notify Seasonal Restrict Border guidance Language Selection Menu Language Voice Recognition
Volume Presets 2D/3D View
Remote Control Route Options Search Condition Route Preferences
Destination
Next passage point or Destination mode Unselected On On On UK English UK English
RDS-TMC Menu Show RDS-TMC info. Dynamic navigation Voice guidance Country
English 37
Stored Locations
English
You can store, edit, or delete any destinations, way points, or marked point.
1 2
Select Select
. (Stored Locations).
3
Select the item you want.
(Memory Points): Places a marker on the map (see page 39). & Way Pt. ): Sets the destination (and way points) (see pages 26 through 28). (Previous Dest. ): Deletes previously stored destinations (and way points) (see page 45). (Preset Dests. ): Stores destinations for a maximum of five buttons (see page 46). (5) Avoid Area (10)
The number in the parentheses indicate the maximum items you can store in the memory.
38 English
Memory Points
Memory Point Storage
Memory points can be classified into one of four categories for storage.
Before Steps
3
(Stored Locations) 3
(Memory Points)
1
Select the category for storage of the memory point.
2
Select
.
3
Set a memory point using your preferred method.
Up to 100 memory points can be stored. [. . . ] The vehicle's mark could also deviate even after the vehicle has exited the parking area. (9) The vehicle's mark could deviate from its actual position if the vehicle is driven on a snow-covered road or on a mountainous road with tire chains or snow tires. · After driving the vehicle under those conditions, perform the same operation given in the section on "After changing tires". (10) The vehicle's mark could deviate from its actual position after the tires have been replaced. [. . . ]