User manual JUNO JDK8730W

[. . . ] -- Please, keep to the provisions of official directives regarding the question of fume discharge. -- The manufacturers refuse to accept any responsibility for damage to the hood or its catching on fire because of failure to observe the above instructions. Fastening the hood to the wall (Fig. 4) -- Position the template in the correct position and make two 8mm diameter holes and two 12mm diameter holes. -- Secure it in place with the two 5x45 mm screws and 5-20 mm diameter washers in the top holes. [. . . ] Ø 125 mm exhausting pipe: insert the multi-connector on the coupling ring and remove, using a proper tool, the upper unused Ø 100 and Ø 110 mm rings of the multi-connector. Ø 110 mm exhausting pipe: same procedure, but removing the Ø 100 mm ring only. Ø 100 mm exhausting pipe: apply the multi-connector on the coupling ring. Warning! -- If the hood is run at the same time as a burner or fireplace that depend on ambient air (for example gas, Diesel, coal or wood heaters, water heaters, etc. ) be careful, because the hood, when it exhausts the air, removes the ambient air required by the burner or fireplace for combustion. -- For secure operation and to prevent discharged gas from coming back in, the vacuum must not exceed 0, 04 mbr. This may be done by making sure the air inlet into the room passes through nonclosing openings such as air recycling wall boxes, doors, windows or with other technical measures. -- No food must be cooked flambé underneath the hood. Electric connection Before completing any connection, make sure the house voltage corresponds with the voltage indicated on the label affixed inside the hood. The hood is supplied with a standard plug; connect it to a correspondingly standard socket. In the case is intended to connect the appliance permanently to the mains after having removed the plug supplied, must be fitted a two-pole switch conforming to regulations with an opening distance between contacts of not less than 3mm. The manufacturers are not liable for any problems caused by the user's failure to observe the above instructions. Installing the duct for recycling version Perform the same operations described in the preceding paragraph. 7) Fasten the four side supports I to the adjacent cabinets and place the shelf on the supports. Operation The hoods JDK 8730 and JDK 9730 are provided with a motor with several speeds. For the best performance, we recommend 14 15 using the low speeds in normal conditions and the high speeds in particular cases of strong odour and vapour concentration. We recommend starting up the hood a few minutes before cooking and keeping it running until all the odours have been eliminated. To start the appliance, pull the control panel downwards for access to the light and motor switches (fig. The hood has a microswitch so that once the motor speed has been selected and the light switched on, the hood can be started by simply pulling out the control panel. The control panel can be positioned at the desired angle to light the cooking area. Therefore, we recommend observing these instructions. I Descrizione della cappa 1) Tasto velocità motore 2) Tasto luce 3) Spia di funzionamento 4) Griglia d'aspirazione 5) Illuminazione piano di lavoro Tubo di scarico di Ø 100 mm: applicare il multiraccordo sulla flangia senza effettuare alcuna modifica sulla stessa. Changing the neon light and starter Versione a riciclo -- Disconnect the hood from the electricity. -- Before calling for technical service because the light fails to work, make sure the components are tightly fastened. L'aria viene filtrata attraverso un filtro al carbone e riciclata nell'ambiente attraverso la sgrigliatura posta sul camino. Si ricorre a questo utilizzo quando non si ha una tubazione di scarico verso l'esterno o non è possibile installarla. Per utilizzarla in questa versione operare come segue: -- Se la cappa è sprovvista di filtro, richiederlo al servizio assistenza tecnica o alla Ditta costruttrice, specificando il modello dell'apparecchio. -- Per montare il filtro, inserirlo nell'apposita sede fissarlo anteriormente con i due agganci B (Fig. [. . . ] Con l'uso del multiraccordo C si possono usare anche tubazioni di Ø 100, 110 e 125mm. Tubo di scarico di Ø 120 mm: non è necessario utilizzare il multiraccordo. Tubo di scarico di Ø 125 mm: inserire il multiraccordo sulla flangia e togliere, utilizzando uno strumento idoneo, gli anelli del multiraccordo di Ø 100 e Ø 110 mm. Tubo di scarico di Ø 110 mm: stesso procedimento del precedente, togliendo solo l'anello del multiraccordo di Ø 100 mm. Attenzione -- Con il funzionamento contemporaneo di una cappa ed un bruciatore o focolare dipendente dall'aria dell'ambiente (come per esempio apparecchi di riscaldamento alimentato a gas, nafta, carbone etc. . . ) si deve fare attenzione, in quanto la cappa, aspirando, toglie all'ambiente l'aria di cui il bruciatore o focolare necessita per la combustione. [. . . ]