User manual JOBO GIGA ONE SONIC

[. . . ] If the GIGA ONE SONIC emits any burnt smell, excessive heat or smoke during battery charging, turn off the power supply immediately and contact your local dealer. Do not operate the GIGA ONE SONIC in wet or moist environments and do not operate the GIGA ONE SONIC with wet hands. If water enters the GIGA ONE SONIC, immediately remove the batteries and return the GIGA ONE SONIC to your local dealer for inspection. Do not use the unit as there is a danger of short-circuit resulting in fire. 3 Table of Content 1. [. . . ] When connected via USB, the GIGA ONE SONIC will charge at 5V, 500mA. 5 You will see the following display screen when battery charging is in progress. Note: You can still charge the battery via USB when the unit is turned on, but you will not see the above battery charging display screen. Charging will automatically stop when the battery is full. 2. 2 Battery Charging (via AC power) Without turning on the GIGA ONE SONIC, plug in the AC adapter to the DC socket on the GIG will be charged at 5V, 1A. You will see the following display screen when battery charging is in progress. Note: You can still charge the battery via AC adapter when the unit is turned on, but you will not see the above battery charging display screen. Getting Started 3. 1 Turning on GIGA ONE SONIC Press the button for 1 second; you will see the following start-up screen and then the Main Menu: GIGA one SONIC 3. 2. Auto Start GIGA ONE SONIC When inserting any type of memory card or microdrive, the GIGA ONE SONIC will automatically switch on. Note: If the GIGA ONE SONIC was turned on automatically by memory card insertion, removal of the memory card will also automatically turn off the GIGA ONE SONIC. 3. 3. Turning off GIGA ONE SONIC From the Main Menu, press the button to turn off the GIGA ONE SONIC. button continuously for 5 s to From any screen, you can also press the turn off the GIGA ONE SONIC. 7 4. Formatting Hard Drive The GIGA ONE SONIC can only operate with FAT32 formatted hard drive. If your hard disk is brand new or not in FAT32 format, you will need to follow the steps below to format the hard drive. Select Feature->Advance->Format: 8 4. 2. Copy Memory Card to GIGA ONE SONIC Insert the memory card; on the Main Menu select Copy: 4. 3. insufficient hard drive space, low battery etc. ) occurs during the memory card copy process, the GIGA ONE SONIC will cease copying and display an error message. At the same time, the LED indicator will blink yellow. Fehlermeldung During then, you have 2 minutes to press to clear the error message, otherwise the GIGA ONE SONIC will shut down and the error message will appear again the next time you turn on the unit. 9 4. 4. file error or bad sector on the memory card) occurs, the GIGA ONE SONIC will cease copy and allow you to either cancel the copy or skip to the next file. If you press, the GIGA ONE SONIC will skip the error file and continue to copy the rest of the memory card. As a safety precaution, the GIGA ONE SONIC will also now copy at the most conservative (normal) speed to ensure maximum memory card compatibility and that all the files are safely retrieved. This is a very useful feature as it will allow you to retrieve the rest of the data on the memory card even if the memory card is defective or damaged. Do note that the error file may still show up on the GIGA ONE SONIC hard drive but it will most likely be corrupted. Date & Time Setup You may set the date and time according to the following steps. Folder Name Setup The GIGA ONE SONIC will create a new folder in the root directory of the hard drive during each backup process. All the data from the memory card will be downloaded into this folder. By default, the new folders will be named SPACEXXX (where XXX will be a sequential number running from 000 to 999). Alternatively you can define your own 8 character folder name as per the following steps. Backup Time Stamping GIGA ONE SONIC is also able to name the folder according to the current time when the folder is created in the format of YYMMDDHH. mms (Year/Month/Day/Hour/minute/second) 6. Transfer Speed Setup Select Setup->Speed: Hyper Speed: Designed for SanDisk Extreme III and Extreme IV CF cards, able to achieve the maximum transfer speed of 20MB/s. [. . . ] STATEMENT & CAUTIONS In order to maintain excellent service the contents of the manual may be subject to change. Yet, product changes in terms of performance and function will no longer be announced. If you find that the methods of use and the settings are not the same as in the manual please visit our website to check the latest product information. Do not use the product under adverse conditions like excessive heat, cold, dust, humidity, etc. [. . . ]