User manual ITS TELECOM PANCAM-C ACCESS CONTROL DOOR PHONES SYSTEM

[. . . ] This guide provides installation and programming instructions for the following products: · PanCam unit · Pantel Outdoor unit · Pantel Indoor unit · Pancode Outdoor unit · Pancode Indoor unit 1. 1 PanCam The PanCam unit is available in two versions: PanCam-C (with keypad) and PanCam-T (one button). Both are wall mounted access control door phones, connected to an analog port of a PBX or a Key Telephone System, with an internal black & white or color high-quality pinhole camera encased within the unit. Both, PanCam-C and T are vandal and weather resistant, suitable for outdoor installation. General Features The PanCam controls the camera, providing three different modes of operation: · Always on · Powered by pressing any button · Powered by pressing the call button Calling the PanCam unit from any extension will activate its camera, enabling the door supervisor to see who is in the direct neighbourhood of the unit. PanCam-C Features The PanCam-C unit has the following features: · Direct dialing to any extension · Speed-dial to internal or external subscribers · Automatic Busy & Disconnect Cadence Detection · Door opening from any extension PanCam/Pantel/Pancode Installation and Programming Manual 1 Introduction · · · · · · · · Programmable day and night destinations Two different operation modes, standard/speed-dial High quality speaker phone with volume control Entry access code Works in conjunction with card readers and security devices Simple to operate and program Smart looking durable design Internal black & white or color high-quality pinhole camera PanCam-T Features The PanCam-T unit has the following features: · Dialing to a pre-defined extension/subscriber · Door opening from any extension · Programmable day and night destinations · Automatic Busy & Disconnect Cadence Detection · Designed for wall mounting · Works in conjunction with card readers and security devices · High quality speaker phone with volume control · Simple to operate and program · Internal black & white or color high-quality pinhole camera 2 PanCam/Pantel/Pancode Installation and Programming Manual Introduction PanCam Physical Description The following figure describes both units. Speaker Camera Key-pad Call button Microphone PanCam-C PanCam-T Figure 2-1. PanCam Front Panel The front panel of the PanCam-T unit incorporates a speaker and a Call button. [. . . ] A bypass switch should be connect to the SW and /SW terminals. Power Supply Normally Open/Closed Outputs Door Lock Relay Terminals Switch Terminals Phone Line/Extension ~12V ~12V N. C. Connector Wiring Note: For the installation of the powered-unlocked-state, use DLR and ~DLR. For the installation of the poweredlocked-state, use /DLR and ~DLR (this is recommended for safety purposes). PanCam/Pantel/Pancode Installation and Programming Manual 11 Installation The wiring connector is a screw connector type. In order to attach a wire you must insert the stripped end of the wire into the proper terminal and tighten the terminal screw. For this installation, the access-control device bypass "Switch" wires are connected to the "N. O. " and "CMN" terminals of the Pantel/Pancode. The door-lock relay wires are connected to the access-control device (see Figure 2-6. ) Lock Relay Pancode/ Pantel N. O. Access Control - Controlling Lock Relay PanCam/Pantel/Pancode Installation and Programming Manual 13 Installation 2. 3 Connection Schematic The Pantel/Pancode offers multiple wiring options. · Option 1: For use with an external device, which requires the Pancode to be set up as "Normally Closed" · Option 2: For use with an external device, which requires the Pancode to be set up as "Normally Open" · Option 3: For use with the powered-unlocked-state lock relay (most common) · Option 4: For use with the powered-locked-state lock relay (recommended for safety purposes) The following schematic diagram shows the wiring plan for these four options. Figure 2-7. PanCam/Pantel/Pancode Wiring Schematics 2. 4 Volume Control The volume of the PanCam/Pantel/Pancode speaker can be adjusted using the volume controller located on the unit's back panel. In case it is too low/high, remove the unit from the mounting bracket and adjust the volume using a small screwdriver. 14 PanCam/Pantel/Pancode Installation and Programming Manual 3 Programming Programming can be done from any telephone or extension on the PBX, using keypad DTMF tones. The following programming functions are discussed in this section: · Day/Night Mode Selection · Entering Programming Mode · Resetting the PanCam/Pantel/Pancode 3. 1 Day/Night Mode Selection Day and Night mode specify which of the programmed destination numbers, Day or Night number, will be called when the Call button is pressed. The operator can manually change the Day/Night mode. To Change the Day/Night Mode 1. Dial the PanCam/Pantel/Pancode line/extension from any touch-tone telephone. Enter *80 for Day Mode -orenter *81 for Night Mode. 3. 2 Entering Programming Mode Note: You will hear a confirmation tone every time you enter a programming command. To Enter Programming Mode 1. Dial the PanCam/Pantel/Pancode line/extension from any touch-tone telephone. Enter the Programming Access Password (default password is 1234). To Exit Programming Mode · Dial *900 ­or­ if no dialing occurs within 45 seconds, the program mode automatically exits. PanCam/Pantel/Pancode Installation and Programming Manual 15 Programming 3. 3 Resetting the PanCam/Pantel/Pancode Resetting the PanCam/Pantel/Pancode will automatically change the parameters in the unit to the manufacturers default. To Reset the Unit 1. Exit programming mode. To Reset the Unit in "speed dial" mode (only PanCam-C and Pancode) 1. Exit programming mode. 3. 4 PanCam-T/Pantel Setup and Operation The following table contains programming functions, which can be accessed in the programming mode for Setup and operation. PBX Parameter Commands OPERATION COMMAND DEFAULT Day, Night destination numbers Delete the destination assignments *360 + X + DN + # where: X = 1; Day destination X = 2; Night destination DN = Up to 20 digits. For special character input, see section 3. 6 Entering Special DTMF Characters. *360 + X + # where: X = 1; Day destination X = 2; Night destination Day = 0 Night = 0 16 PanCam/Pantel/Pancode Installation and Programming Manual Programming OPERATION COMMAND DEFAULT *For Pantel Indoor ONLY: Busy off/on time cadence setups for disconnecting the line when the destination is busy Digit(s) to open the door from any extension *For Outdoor units ONLY Time between DTMF's Maximum time for the line to be opened (sec) Door opening time limit (sec) Change the system administrator's password *For PanCam-T ONLY Camera instructions *371 + X + YYYY where: X = 1; off time setup X = 2; on time setup YYYY = Cadence in steps of 20 milliseconds *441 +XXXX + # where: XXXX = Digits (0-9) Note: Up to 4 digits *460 + X where: X = 1-9 (Each step is 200 msec) *462 + XX XX = Seconds (10-99) 00 = Unlimited *464 + X X = Seconds (1-9) *600 + New password (must be 4 digits). Warning: Do not use the * or # keys *620 + X X = 0 camera off X = 1 camera on X = 2 camera powered when call button is pressed 500 msec 500 msec 8 2 (400ms) 45 sec 3 sec 1234 0 PanCam/Pantel/Pancode Installation and Programming Manual 17 Programming 3. 5 PanCam-C/Pancode Setup The PanCam-C/Pancode can work in two modes of operation: Standard and Speed-dial. In Standard mode, which is the default, the keypad requires direct dialing of extensions and numbers. [. . . ] If the new access code is less than four numeric digits, press the # key following entry of the digits. *460 + X where: X = 1-9 (each step is 200 msec) *462 + XX XX = Seconds (10-99) 00 = Unlimited *464 + X XX = Number of seconds (1-9) *600 + (new password) Programming access passwords must be four numeric digits. Do not use the * or # keys. 8 0123 *For Outdoor units ONLY Time between DTMF's Conversation time limit (sec) Door opening time limit (sec) Changing the programming password 2 (400) 45 sec 3 sec 1234 22 PanCam/Pantel/Pancode Installation and Programming Manual Programming OPERATION COMMAND DEFAULT *For PanCam-C Camera instructions *620 + X X = 0 camera off X = 1 camera on X = 2 camera powered when call button is pressed X = 3 powered by any touch on unit keypad 0 3. 6 Entering Special DTMF Characters Special characters can be entered using the keypad. The following table shows the corresponding keypad entries needed for creating special DTMF characters. DTMF CHAR. [. . . ]