User manual ITS TELECOM CGW-TS INSTALLATION RELEASE 4 REV 3

[. . . ] 8 GSM Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CDMA Gateway (CGW-T Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 SIM Card Insertion into the Unit (GSM only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If, for any reason, you are unable to do so using an analog telephone connected to the CGW-T/TS FXS RJ-11 port, use any GSM mobile phone to modify the SIM card, or contact your local GSM Service Center. 3. 2 CDMA Gateway (CGW-T Only) The CGW-T (CDMA) contains a CDMA engine that needs to be activated via a local CDMA network provider. You register the engine the way you would normally register a mobile CDMA phone. NOTE It is recommended that you disable all call forwarding modes (in the events of busy, absence, unavailability, etc. ) and Call Waiting from the GSM/CDMA operator, before installing the SIM card (GSM network), or activating the CDMA unit. 8 CGW-T/TS Installation and Programming Manual 4 4. 1 Installation SIM Card Insertion into the Unit (GSM only) CAUTION To avoid damage to the CGW-T/TS unit, disconnect the 9V adapter from the electric power outlet. The physical description of the unit can be used as guideline for the following steps: Hold the unit in your hands with the display pointed to your left and the SIM insertion slot at the bottom of the unit towards you (so that the text "SIM" is upside-down). Using a screwdriver, push the yellow SIM release lever, so that the SIM card tray moves towards you. Carefully place the tray with the SIM card in the slot and slide it in with the SIM card contacts facing down. 4. 2 CGW-T/TS Installation Mount the CGW-T/TS unit on the wall as a stand-alone unit or on the 6-fold wall mount bracket, which is a separate accessory. Connect the analog trunk interface of the PBX to the trunk connector on the front panel of the CGW-T/TS unit. At the end of the process, the LCD will display the signal status. To install the CGW-T/TS unit, perform the steps as follows: NOTE Adjust the antenna location until an optimal signal level is received. Figure 3 displays the schematic setup of the CGW-T/TS unit. 10 CGW-T/TS Installation and Programming Manual Figure 3. CGW-T/TS Schematic Setup 5 5. 1 LCD Status Indicators and Diagnostics CGW-T LCD Status Indicators and Diagnostics The CGW-T Gateway can be connected to the analog trunk interface of the PBX. At powerup of the CGW-T unit, the information on the LCD will provide the first diagnostics. By connecting an analog telephone with the RJ-11 connector to the trunk connector in the unit, you are able to perform further diagnostics. 5. 1. 1 LCD Status Indicators The following table shows the messages appearing on the LCD, their description and the action to be taken (if any). Action No action needed. Enter PIN code (GSM only) CGW-T needs the PIN code to activate the SIM card. 1. Alternatively, insert the SIM into your mobile phone and disable the security option. 12 CGW-T/TS Installation and Programming Manual LCD Message Enter PUK code (GSM only) Registration. . . Description CGW-T received 3 times an incorrect PIN code. LCD shows signal level in dBm Name of Operator (read from mobile network). CGW-T gets a call from network. Action Request the PUK code from your local GSM operator and enter it into the CGW-T. If level is below 85 dBm, move the antenna to another location with a better reception. Connected Disconnected Incoming Call LCD Message Description CGW-T receives incorrect operation information from the mobile network. GSM/CDMA engine problem. Action Failed Try again. Engine Problem Power off and on the unit. Insert SIM card. No Signal No Signal or Signal low (less than 108 dBm). Reg. Denied Insert SIM Card (GSM only) Registration denied and/or SIM card is not readable. No SIM card inserted. 14 CGW-T/TS Installation and Programming Manual 5. 1. 2 CGW-T Diagnostics Perform the diagnostic procedure as follows: Connect an analog telephone directly to the trunk connector (RJ-11) on the unit front panel. Pick up the receiver and listen to the dial tone: A continuous dial tone indicates that the unit is working correctly and ready for programming. Check the LCD display for a message. NOTE If there is no SIM card in the device, or if the card is not installed properly, there will be no tone on the CGW-T, whereas on the CGW-D the tone will be that of the PSTN line. 5. 2 CGW-TS LED Status Indicators and Diagnostics When you power-up the CGW-TS, the LEDs indicate the first diagnostics. [. . . ] The device disconnects when a busy tone is detected for XX seconds Tone Detect Timer ­ time interval for continuous tone detection. The device disconnects when a continuous tone is detected for XX seconds Command *500 + X where: X = 0, off X = 1, on 0 Default *520 + XX Where XX ­ time in seconds (an error rate of ±25% may occur due to busy tone cadence). *530 + XX Where XX ­ time in seconds (an error rate of ±25% may occur due to tone flexibility). 6 6 Operation No Voice Detect Timer ­ time interval for silence detection. The device disconnects when silence is detected for XX minutes CLIR (Calling Line Interface Restriction) The CGW-T can be restricted to show its SIM telephone number. [. . . ]