User manual INTEL DESKTOP BOARD D510MO
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual INTEL DESKTOP BOARD D510MO. We hope that this INTEL DESKTOP BOARD D510MO user guide will be useful to you.
You may also download the following manuals related to this product:
INTEL DESKTOP BOARD D510MO (4239 ko)
Manual abstract: user guide INTEL DESKTOP BOARD D510MO
Detailed instructions for use are in the User's Guide.
[. . . ] Intel Desktop Board D510MO Product Guide
Order Number: E74518-001
Revision History
Revision -001 Revision History First release of the Intel Desktop Board D510MO Product Guide Date September 2009
If an FCC declaration of conformity marking is present on the board, the following statement applies:
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation, 5200 N. E. Elam Young Parkway, Hillsboro, OR 97124, 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] See Figure 12, F on page 34 for the location of the front panel header. Front Panel Header Signal Names
Pin Signal In/Out Description Pin Signal In/Out Power LED HDR_BLNK_GRN HDR_BLNK_YEL Out Out Front panel green LED Front panel yellow LED Power switch Ground Not Connected Power 10 N/C No pin Description Hard Drive Activity LED 1 3 HD_PWR HDA# Out Out Hard disk LED pull2 up (330 ?) to +5 V Hard disk active LED Ground Reset switch Power 9 +5 V 4
Reset Switch 5 7 Ground FP_RESET# In 6 8 Ground
On/Off Switch SWITCH_ON# In
Connecting to the Front Panel USB 2. 0 Headers
Before connecting to the USB 2. 0 headers, observe the precautions in "Before You Begin" on page 23. See Figure 12, G and H on page 34 for the location of the USB 2. 0 headers. The brown USB header (Figure 12, G) supports a single USB port while the black USB header (Figure 12, H) supports two USB ports. The single USB port header is designed to support a Flash Memory Drive such as the Intel Z-U130 USB Solid-State Drive (or compatible device). Refer to Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device) on page 33 for more information. Front Panel USB Header
Pin 1 3 5 7 9 Signal Name
+5 VDC DD+ Ground KEY (no pin)
Pin 2 4 6 8 10
Signal Name
+5 VDC DD+ Ground No Connect
38
Installing and Replacing Desktop Board Components
Table 14. Front Panel USB Header with Intel Z-U130 USB Solid-State Drive (or Compatible Device) Support
Pin 1 3 5 7 9 Signal Name
+5 VDC DD+ Ground KEY (no pin)
Pin 2 4 6 8 10
Signal Name
No Connect No Connect No Connect No Connect LED#
Connecting a Chassis Fan
Figure 13 shows the location of the chassis fan header. Location of the Chassis Fan Header
39
Intel Desktop Board D510MO Product Guide
Connecting the Power Supply Cable
CAUTION
Failure to use an appropriate power supply to the Desktop Board may result in damage to the board or the system may not function properly. Connect the main power supply cable (2 x 12) to the 2 x 12 connector (Figure 14).
40
Installing and Replacing Desktop Board Components
Setting the BIOS Configuration Jumper
NOTE
Always turn off the power and unplug the power cord from the computer before changing a jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 15 shows the location of the Desktop Board?s BIOS configuration jumper block.
Figure 15. BIOS Configuration Jumper Block The three-pin BIOS jumper block enables board operating modes. Table 15 shows the jumper settings for each of the available modes.
41
Intel Desktop Board D510MO Product Guide
Figure 15 shows the location of the Desktop Board?s BIOS configuration jumper block. Jumper Settings for the BIOS Setup Program Modes
Jumper Setting Mode Normal (default) (1-2) Description The BIOS uses the current configuration and passwords for booting.
Configure (2-3)
After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords.
Recovery (None)
The BIOS recovers data from a recovery diskette in the event of a failed BIOS update.
Clearing Passwords
This procedure assumes that the board is installed in the computer and the configuration jumper is set to normal mode. Disconnect the computer?s power cord from the AC power source (wall outlet or power adapter). Replace the cover, plug in the computer, turn on the computer, and allow it to boot. Press <Enter> and Setup displays a pop-up screen requesting that you confirm clearing the password. Press <F10> to save the current values and exit Setup.
42
Installing and Replacing Desktop Board Components
10. To restore normal operation, place the jumper on pins 1-2 as shown below.
13. Replace the cover, plug in the computer, and turn on the computer.
Replacing the Battery
A coin-cell battery powers the Desktop Board?s real-time clock and CMOS memory. [. . . ] EMC Regulations
Regulation (Class B) FCC 47 CFR Part 15, Subpart B ICES-003 Issue 4 EN55022:2006 Title Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency Devices. (Canada) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. (European Union) Australian Communications Authority, Standard for Electromagnetic Compatibility. (Australia and New Zealand) Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE INTEL DESKTOP BOARD D510MO
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual INTEL DESKTOP BOARD D510MO will begin.