User manual INFOCUS IN82 Reference Guide

[. . . ] IN82 User's Guide Mode d'emploi Benutzeranleitung Manual de Uso Guidaall'uso Gebruikershandleiding Guia do usuário Användarhandbok Declaration of Conformity Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands We declare under our sole responsibility that this projector conform to the following directives and norms: EMC Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC Safety: IEC 60950-1: 1st Edition July, 2007 FCC Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] HDTV and most DVDs are 1. 78:1, or 16:9 (the projector's default). Choose the option that best fits your input source in the menus, or press the Resize button on the remote to cycle through the options. See your DVD player's user's guide for instructions. Customizing the projector You can customize the projector for your specific setup and needs. · · · · · · · For rear projection, turn rear mode on in the Settings>System menu. For ceiling mounted projection, the projector has an Auto Ceiling feature to invert the image (Settings>System menu). Save settings for the active source as a preset. · · · 18 Using the menus To open the menus, press the Menu button on the remote. (The menus automatically close after 60 seconds if no buttons are pressed. ) The Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button. To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. When your adjustments are complete, navigate to Previous or Exit, then press Select to go to the previous menu; press the Menu button at any time to close the menus. The number of dots indicate menu's level, ranging from one (the Main menu) to four (the most nested menus). The menus are grouped by usage: · · · The Picture menu provides image adjustments. The Settings menu provides set-up type adjustments that are not changed often. The Source Info menu provides a read-only display of information about the projector and source. Settings menu Main menu remote navigation buttons Picture menu dots Certain menu items may not be visible or may be grayed depending upon a particular source being connected. Differences are also seen in analog versus digital video sources and interlaced versus progressive sources. Menu options are grayed out only if the source is selected but no signal is present. For example, if the projector is set to a video source but the source, such as a DVD player, is turned off video menu options are grayed out. Source Info menu 19 Picture menu To adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes. Tilt the projector up or down to adjust for keystone before using the digital keystone correction in the menu. Use to shift the image, or to mask artifacts or bars on the top or bottom of the image. Contrast: controls the degree of difference between the lightest and darkest parts of the picture. Color: adjusts a video image from black and white to fully saturated color. Tint: adjusts the red-green color balance in the image of NTSC video images. [. . . ] Service Info: provides information about the projector's software, serial number, and lamp. Source Info: provides information about the active source. Service menu HDMI menu Serial Port menu Service Info Source Info menu 26 Maintenance Replacing the projection lamp The lamp hours timer in the Service Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, a message appears on the screen at startup indicating that you should change the lamp. The LED on top of the projector also blinks red twice to indicate that the lamp should be changed. [. . . ]