User manual INFINITY PSW310W

[. . . ] To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable. Do not expose batteries to excessive heat such as sunshine, fire or the like. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] When connected properly, the LED ¢ on the rear of the subwoofer will be orange. Set the Low-Pass Selector to the "Off" position. If your receiver/processor does not contain a Dolby Digital or DTS processor but has subwoofer outputs: receiver/proceSSor green: sub On Red: standby Orange: sub On and Wireless link active NOTE: If your receiver/processor has only one sub out, you may use either the L or R input. 6 INFINITY CLASSIA PSW310W (230V) oPeratIon Power On Connect your signal source (such as an A/V receiver or preamplifier) to the transmitter (if using wireless connection) or to the subwoofer (if using wired connection). While you would ordinarily use the short cable to connect to the transmitter or the long one to connect to the subwoofer, either cable can be used, depending on proximity to the signal source. There is no need or benefit gained from connecting the same source to both the transmitter and the subwoofer. However, you could connect two separate sources to this subwoofer by utilizing both its wired and wireless connections. Both signals will essentially be mixed and outputted by the subwoofer. Plug your transmitter's (if using wireless connection) and subwoofer's AC cord into a wall outlet. Initially set the Subwoofer-Level Control · to the "Min" position. Turn on your sub by pressing the Power Switch ¡ on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Getting Started Confirm that the Status LED on the transmitter (not shown) is on (red or green) and the Status (Power Indicator) LED ¢ on the subwoofer is on (red, orange or green) and that an RCA cable is connected from a source unit to either the LFE Input £ of the subwoofer or transmitter H or L and R inputs TM on the subwoofer. If using a wireless connection, the Status LED on the transmitter should be lit in solid green, and the Status LED ¢ on the subwoofer should turn orange if connected wirelessly. If the LED on the transmitter is blinking in green and the LED on the subwoofer is in red or green, a wireless link has not been established between the transmitter and the subwoofer. If connecting directly to the subwoofer without using the wireless link, the Status LED ¢ on the subwoofer should be lit green. If the LED on the subwoofer remains red, check that the RCA cable from the source to the subwoofer (wired connection) or transmitter (wireless connection) is functioning properly (wired connection) and that it is fully inserted at both ends, or that the Transmitter ID-Code Selector G and the Subwoofer ID-Code Selector § are set to the same channel. Once you have a green or orange LED on the subwoofer, turn your Subwoofer-Level Control · up halfway so that the knob indicator points up. Proper phase adjustment depends on several variables such as room size, subwoofer placement and listener position. Adjust the phase switch to maximize bass output at the listening position. Crossover Adjustments The Crossover Adjustment Control ¶ determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz. This will concentrate the subwoofer's efforts on the ultradeep bass sounds required by today's films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the Crossover Adjustment Control to a higher setting, between 120Hz and 150Hz. INFINITY CLASSIA PSW310W (230V) 7 ENGLISH NOTE: This control will have no effect if the LFE Input £ is used (wired connection) or if the Low-Pass Selector is in the "OFF" position (wireless connection). If you have a Dolby Digital or DTS processor/ receiver, the Low-Pass Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting. room adaPtIve bass oPtImIzatIon system TM ID Codes In the unlikely event that you experience interference when operating the system, or if you have more than one set of subwoofer transmitters and receivers in operation, you may change the channel in which the system operates. [. . . ] Stains may be removed with an aerosol cleaner, following its instructions. All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions, and other factors, but once per year is the minimum. In the event that your subwoofer ever needs service, contact your local Infinity dealer or distributor or visit www. infinitysystems. com for a service center near you. [. . . ]