User manual INFINITY PHI 21

[. . . ] PHI 51 - PHI 21 Owner's Guide ENGLISH PHI OWNER'S GUIDE Table of Contents 3 4 4 4 5 5 6 6 7 8 9 9 10 Important safety precautions Introduction Unpacking the System Planning Your System Placement Wall-Mounting the Satellites Assembling the Floorstands Center and Satellite Speaker Connections Subwoofer Controls Subwoofer Connections Operation Maintenance and Service Specifications 2 PHI 51 - PHI 21 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To prevent electric shock, do not remove the grounding plug on the power cord, or use any plug or extension cord that does not have a grounding plug provided. Do not use an adapter plug with this product. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Declaration of Conformity We, Harman Consumer Group, Inc. 2, Route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility that the product described in this owner's manual is in compliance with technical standards: EN 61000-6-3-2001 EN 61000-6-1-2001 EN 55013: 2001+A1-2003 EN 55020: 2002+A1-2003 EN 61000-3-2: 2000 EN 61000-3-3: 1995+A1-2001 EN 60065: 2002 Laurent Rault Harman Consumer Group International Chateau-du-Loir, FRANCE 2/08 read first! [. . . ] Use a shelf if the television does not provide a stable platform. WALL-MOUNTING THE SATELLITES The PHI satellites are designed to be mounted on the wall. Note: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the speakers. Mark the positions on the wall where you would like to place the mounting screws. Place bracket against wall and fasten two appropriate screws through the bracket's screw holes into the wall. The wall brackets have a hole in the back for cables that are installed into the wall. Make sure that enough cable is free to reach the plus and minus terminals on the back of the speaker and then dress it through the hole in the bracket before securing the bracket onto the wall. After having secured the bracket on the wall with the wire hanging through the hole, attach the two leads to the terminal screws on the speaker, and secure the speaker to the wall bracket with the single central screw. Surround Channels For left and right surround channels, place one speaker on the left and another on the right, to the side of or slightly behind the listening area. The surround speakers should be mounted at a height of between 1. 2 and 2 meters. Subwoofer Since the installation of a subwoofer can be somewhat more complicated than installing full-range speakers, it is essential that you read this section very carefully prior to connecting the subwoofer to your system. Should you have questions relating to installation, it is advisable to call either your dealer or Infinity's Customer Service Department for advice. The performance of the subwoofer is directly related to its placement in the listening room and how you align the subwoofer with the satellite speakers. Setting the volume of the subwoofer in relation to the left and right speakers is also of critical importance because it is essential that the subwoofer integrate smoothly with the entire system. Setting the subwoofer's volume level too high will result in an overpowering, boomy bass. Use the speaker wire provided, or use high-quality speaker wire with polarity coding to make your connections. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). Also, consult the owner's manuals that were included with your amplifier or reciver to confirm connection procedures. All wires are connected with either bare copper wires or spades fixed to the screw-head binding posts. Secure the stand base to the column and tighten the two supplied fixing screws. Connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker. Connect the ­ (black) terminals in the same way. Attaching the stand to the speaker 1. Pull enough cable out of the top of the column to allow it to reach the speaker terminals comfortably when the satellite is fixed in position. Attach the speaker to the stand with the supplied long screw. 1 Insert Bare End; Tighten Terminal 0 Loosen No Stripe = Stripe = + Speaker Wire Terminal Important! Do not reverse polarities (i. e. , + to ­ or ­ to +) when making connections. Be certain that positive and negative wire strands are completely isolated to avoid short circuits that may damage your equipment. [. . . ] This means that whenever your main system or receiver is switched OFF, the subwoofer goes to OFF as well. "Auto" is meant for systems that do not offer the use of a trigger signal. In Auto mode, the subwoofer "listens" for a signal, and switches ON whenever a signal is present. This means that if there is almost no sound entering the subwoofer for a while, it shuts off, only to "wake up" again whenever a sound arrives. [. . . ]