User manual HP OFFICEJET PRO 8000

[. . . ] OFFICEJET PRO 8000 User Guide A809 HP Officejet Pro 8000 (A809) Printer Series User Guide Copyright information © 2009 Copyright Hewlett-Packard Development Company, L. P. Hewlett-Packard Company notices The information contained in this document is subject to change without notice. Reproduction, adaptation, or translation of this material is prohibited without prior written permission of HewlettPackard, except as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. [. . . ] For more information, see Turn off the device. Troubleshooting tips and resources Use the following tips and resources to resolve printing problems: · · · · · For a paper jam, see Clear a jam in the device. For paper-feed problems, such as the paper skew and paper pick, see Solve paper-feed problems. When the device is turned on for the first time, it takes approximately 20 minutes to initialize it after the printheads are installed. Power cord and other cables are working, and are firmly connected to the device. Make sure the device is connected firmly to a functioning alternating current (AC) power outlet, and is turned on. Media is loaded correctly in the tray and is not jammed in the device. Printheads and ink cartridges are properly installed in their correct color-coded slots. All packing tapes and materials are removed. · · · · · 66 Maintain and troubleshoot · · · · The device can print a configuration page. For Mac OS X, set it as the default in the Printer Setup Utility (Mac OS X (v10. 4), for Mac OS X (v10. 5) open System Preferences, select Print & Fax, and then select the device from the Default Printer drop-down list. ) See your computer's documentation for more information. Pause Printing is not selected if you are using a computer running Windows. Close programs that you are not using or restart the computer before attempting the task again. To set a static IP address 1. Open the embedded Web server, click the Networking tab, click Wired (802. 3) or Wireless (802. 11) in the left pane, and then click the IPv4 Configuration or IPv6 Configuration sub-tab. Select Manual IP, and then type the static IP address in the Manual IP Address box. Enter the Manual Subnet Mask and the Manual Default Gateway, if necessary, and then click Apply. CAUTION: Changing the IP address can disrupt the current connection to the embedded Web server. Solve printing problems · · · · · · · The device shuts down unexpectedly The device is not responding (nothing prints) Printer lights are blinking Device takes a long time to print Placement of the text or graphics is wrong The device prints half a page, then ejects the paper Device is printing from the wrong input tray The device shuts down unexpectedly Check the power and power connections Make sure the device is connected firmly to a functioning alternating current (AC) power outlet. For voltage requirements, see Electrical specifications. The device is not responding (nothing prints) If the device supports wireless communication, see also Solve wireless problems. Check the device setup For more information, see Troubleshooting tips and resources. Solve printing problems 67 Chapter 5 Check the printhead initialization When printheads are installed or replaced, the device automatically prints a few alignment pages to align the printheads. Until this process is complete, only the automatic alignment pages can be printed. Check the device software installation If the device is turned off when printing, an alert message should appear on your computer screen; otherwise, the device software might not be installed correctly. To resolve this, uninstall the software completely, and then reinstall the device software. Check the cable connections · Make sure both ends of the network/USB cable are secure. · If the device is connected to a network, check the following: Check the Network button on the control panel. [. . . ] ECC cipher suite support in OpenSSL originally developed by SUN MICROSYSTEMS, INC. , and contributed to the OpenSSL project. SHA2 FIPS 180-2 SHA-224/256/384/512 implementation Last update: 02/02/2007 Issue date: 04/30/2005 Copyright (C) 2005, 2007 Olivier Gay <olivier. gay@a3. epfl. ch> All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. [. . . ]