User manual HITACHI VT-FX540E(UK)

[. . . ] Owner's Manual Please read before using this product. IMPORTANT COPYRIGHT INFORMATION Unauthorised recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright laws. We do not take responsibility for the unauthorised duplication, use, or other acts which infringe upon the rights of copyright owners. A NOTE ABOUT RECYCLING This product's packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. [. . . ] 6 Press thePLAY/oor STOP/L button repeatedly until the channel move to another position number, then press the F. FWD/Bbutton. 7 Press the MENU button. MANUAL POSITION CHANNEL DECODER SKIP P08 008 [OFF] [OFF] CH TUNING AUTO MANUAL MOVE To Skip a Preset Channel The channels you can no longer receive or seldom watch can be set to be skipped when you access channels with the PROGRAM (o/p) buttons. 2 Press the PLAY/oor STOP/Lbutton to select "INITIAL", then press the F. FWD/Bbutton. 3 Press the PLAY/oor STOP/Lbutton to select "CH TUNING", then press the F. FWD/Bbutton. 4 Press the PLAY/oor STOP/Lbutton to select "MANUAL", then press the F. FWD/Bbutton. 5 Press the PLAY/oor STOP/Lbutton to select "POSITION", then press the F. FWD/Bbutton. 6 Press number buttons, the PLAY/oor STOP/Lbutton to select relevant position number, then press the F. FWD/Bbutton. 7 Press the PLAY/o or STOP/L button to select "SKIP", then press the F. FWD/Bbutton to select [ON]. NOTE: · To confirm that a channel has been deleted, press the PROGRAM (o/p) buttons. MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK RF OUT MOVE P01: P02: P03: P04: P05: 01 02 [03 ] 04 05 P06: P07: P08: P09: P10: 06 07 08 09 10 CH TUNING AUTO MANUAL MOVE MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK RF OUT Position Number Channel Number MOVE P01: P02: P03: P04: P05: MANUAL POSITION CHANNEL DECODER SKIP P08 008 [OFF] [ON] CH TUNING AUTO MANUAL MOVE 01 02 10 04 05 P06: P07: P08: P09: P10: 06 07 08 09 [03] MOVE P01: P02: P03: P04: P05: 01 02 10 04 05 P06: P07: P08: P09: P10: 06 07 08 09 03 10 EN BASIC OPERATION Playback Tracking Adjustment · Tracking adjustment will be activated automatically (Digital Tracking function) when you start playback. · When playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the PROGRAM (o/p) buttons on the remote control or front panel until the streaks disappear. To return to the DTR function, stop the tape once and start playback again. NOTES: · You can reduce the noise lines by pressing the PROGRAM (o/p) buttons in Slow mode, too. · In the Still mode, press the SLOW button, and press the PROGRAM (o/p) buttons until the streaks disappear. If the erase-protection tab has been removed, the VCR will start playback automatically. · Tracking adjustment will be activated automatically (Digital Tracking function) when you start playback. <If a tape is already in the VCR. . . > · Using the buttons on the VCR Just press the PLAY button on the VCR. (Direct Button Operation) · Using the buttons on the remote control Press the OPERATE button to turn on, and then press the PLAY button. 4 Press the STOP button to stop playback. Slow Motion · Press the SLOW button to reduce the playback speed. You can control the speed by pressing the F. FWD (faster) or REW (slower) button. · If it is left in the Slow mode for more than five minutes, the VCR will automatically switch to the Stop mode. Recording Viewing and Recording the same Programme 1 Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) 2 Press the NUMBER or PROGRAM (o/p) buttons to select the channel to be recorded. [. . . ] Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people. DON'T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. DON'T listen to headphones at high volume, as such use can permanently damage your hearing. [. . . ]