User manual HITACHI UT47V702

[. . . ] TM UltraVision HDTV Monitors 1. 5" UltraThin Liquid Crystal Display Anthracite Pearl Crystal Frame 1920 x 1080p 120Hz PictureMasterTM VI with Reel 120TM (1) HDMITM (V. 1. 3 with CEC) Input; (1) RGB D-sub15 Input with Audio Operating Guide UT37V702 UT42V702 UT47V702 READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. Model Name Record the serial number of your monitor for future reference. SERIAL NO. This serial number is located on the back and right side of the monitor. ANY QUESTION ABOUT THIS PRODUCT PLEASE CONTACT 800-Hitachi CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Always be sure to connect the power cord to a three-pin grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line. If you have to change the power cord, please use a certified power cord that meets your region's safety standards. 21 BASIC OPERATION ENGLISH 22 Power On/Off Turn On the power of the unit. Illumination Lamp Indicating Lamp To turn On the power to the unit: 1. The Indicating Lamp illuminates in Green, and the Illumination Lamp turns Blue. Once the Main Power switch is on, you can turn On/Off by pressing the Power (On/Off) button on the remote control. Main Power Switch (on the underside) Front To turn Off the power to the unit: 1. The Indicating Lamp turns Red (Standby mode), and the Illumination Lamp turns off. Press the Main Power switch on the unit to completely turn Off the power to the unit. NOTE Rear Power On/Off button While the Indicating Lamp illuminates in Red (Standby mode), you can turn On/Off by pressing the Power (On/Off) button on the remote control. The Indicating Lamp/Illumination Lamp Status Indicating Lamp Off Red Green Orange Blinking Green NOTE Illumination Lamp ­ ­ Blue ­ Blue Power Status Off Standby mode On Power Save mode On Refer to 42 Remark ­ ­ ­ and 43 for the condition. Receiving Remote Control signal If the image does not appear on the screen at all, or if there is any problem with it, see "TROUBLESHOOTING" on 43 ~ 45 . After turning On, it takes about 6 seconds until the monitor starts up. Please note that buttons on the remote control and the unit (such as the Power button) do not work during this period of time. If power is interrupted during use of the unit, to avoid sudden surges of electricity when the power comes back on, turn off the main power to the unit before leaving home. BASIC OPERATION (continued) Volume Up/Down 1. To increase the sound volume, press the Volume Up button on the remote control or control panel. To decrease the sound volume, press the Volume Down button on the remote control or control panel. The color of the Volume Indicator will turn into grey while muting the volume. To turn the sound back on, press the button again, or press the Volume Up button on either the remote control or control panel. The color of the Volume Indicator will turn back to blue. NOTE Volume Up/Down button 20 You can decrease the volume by pressing the Volume Down button while the sound is muted. 23 BASIC OPERATION (continued) Menu button By pressing the Input Select button , you can switch the input to display the image outputting from the external equipment connected to each terminal (HDMI and RGB (/Composite)). Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select button RGB Input Select button HDMI Input Select button Press the or button to directly select the input mode. <From Control panel> The Input modes can also be switched using the Input Select button on the control panel. Each time this button is pressed, the screen displays the corresponding mode in the following sequence. HDMI RGB (/Composite) Input Select NOTE Switching between RGB and Composite Mode When pressing button, you will see the image from either RGB or Composite mode. Select "Composite" to display the image from a video source via the optional D-sub 15 pin - composite cable. See 38 and 39 for details of "RGB input" menu. Input Signal Screen Display The input signal status can be displayed on the screen by pressing the button on the remote control. Input mode HDMI mode HDMI DVI 720p * Signal mode * HDMI-DVI connection only RGB mode Input mode Input horizontal frequency Input vertical frequency INFO button RGB H : 48. 4kHz V : 60. 0 Hz Composite mode Composite 24 ENGLISH Input Switching to HDMI and RGB SETUP OPERATION How to Use the Remote to Control your External Devices OPERATING THE PRECODED FUNCTIONS FOR YOUR EXTERNAL DEVICES. [. . . ] You understand and agree that your use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys' fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement. The Software is protected by federal copyright laws, international copyright treaties and other intellectual property laws and treaties. [. . . ]