User manual HITACHI UT32S402

[. . . ] TM Hitachi UltraVision® 1. 5TM UltraThin LCD HDTV with Audio Video Center 32" Class (31. 51" Diagonal) Anthracite Pearl Crystal Frame 1366 x 768p 120 Hz, PictureMasterTM V (3) HDMITM (V. 1. 3 with Deep Color, CEC) Inputs; (2) Component Inputs Operating Guide UT32S402 Model Name READ THE ENCLOSED INSTRUCTIONS CAREFULLY. KEEP THIS OPERATING GUIDE FOR FUTURE REFERENCE. Record the serial number of your monitor for future reference. SERIAL NO. This serial number is located on the back and right side of the monitor. If you have a question about this product please call 800-Hitachi for assistance CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . 02 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For details of the output format of an external device, refer to "Recommended Signal List" on 50 . Connect your Equipment to the A/V Center (continued) Connecting to Equipment Having a Audio Digital Input Terminal The A/V Center "OPTICAL OUT" Audio terminal can be connected to devices equipped with Optical Input capabilities such as Audio Amplifiers Systems. The "OPTICAL OUT" from the A/V Center Rear Panel is a fixed output. The Volume of the amplifier is controlled by the amplifier, not by the A/V Center Unit. The OPTICAL OUT terminal outputs all audio sources. Optical OUT [Example] OUT IN OPTICAL IN (Audio) STEREO SYSTEM AMPLIFIER 2. Connecting to a PC(on Monitor Side) The PC connection terminal (D-sub 15 pin) + the PC (RGB) Analog Audio Input terminal are connected to the PC, allowing an analog RGB signal. IN OUT AUDIO (D-sub 15 Pin) To insert D-sub 15 pin, tilt the monitor forward and bring the terminals into view. Two people are required to hold the monitor and insert D-sub 15 pin safely. Be careful not to damage the panel. Tilt Forward * D-Sub 15 * Audio Cable NOTE *D-sub 15 and Audio cables are not included. CONNECTION (continued) 3 . C o n n e c t i n g t o E q u i p m e n t H av i n g V i d e o O u t p u t Terminals ( on Monitor side) The Monitor can be connected to equipments having video output using the optional D-sub 15 pin - composite cable. Your UT Monitor is capable to receive composite video, you can watch images from your external equipments through the optional D-sub 15 pin - composite cable, but A/V Center provides more practical terminals. [Example] VCR IN AUDIO OUT (Audio) or DVD player * (D-sub 15 Pin) Set-Top Box Camcorder * Optional D-sub 15 pin - composite cable. Home video game system 4. Connect the Power Plugs into the Wall Socket Monitor Back Side Monitor Rear Panel AC Wall Socket A/V Center Back Side AVC Rear Panel AC Wall Socket CAUTION Use only the power cord provided. Do not use a power supply voltage other than that indicated (AC120, 60Hz). For the LCD monitor, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pin grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line. If you have to change the power cord, please use a certified power cord that meets your region's safety standards. 23 BASIC OPERATION ENGLISH 24 Power On/Off Turn On the power of the unit. Illumination Lamp Indicating Lamp To turn On the power to the unit: 1. The Indicating Lamp illuminates in Green on Monitor/Blue on A/V Center, and the Illumination Lamp turns Blue. Once the Main Power switch is on, you can turn On/Off by pressing the Power (On/Off) button on the remote control. Main Power Switch (on the underside) Front To turn Off the power to the unit: 1. The Indicating Lamp turns Red (Standby mode) on Monitor and A/V Center, and the Illumination Lamp turns off. Press the Main Power switch on the Monitor to completely turn Off the power to the Monitor. NOTE Rear Power On/Off button While the Indicating Lamp illuminates in Red (Standby mode), you can turn On/Off by pressing the Power (On/Off) button on the remote control. The Indicating Lamp/Illumination Lamp Status of the Monitor Indicating Lamp Off Red Green Orange Blinking Green Illumination Lamp ­ ­ Blue ­ Blue Power Status Off Standby mode On Power Save mode On Refer to 44 Remark ­ ­ ­ for the condition. Receiving Remote Control signal The Indicating Lamp Status of A/V Center Indicating Lamp Off Red Blue NOTE Power Status Off Standby mode On If the image does not appear on the screen at all, or if there is any problem with it, see "TROUBLESHOOTING" on 45 ~ 47 . [. . . ] You understand and agree that your use of the Software in any manner except as permitted under this Agreement could constitute a serious crime and could subject you to damages and an award to HITACHI of attorneys' fees in connection with your violation of this Agreement. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights caused or facilitated by your failure to abide by the terms of this Agreement. You agree to defend, indemnify and hold HITACHI and its parent and affiliate companies harmless from and against any and all liability resulting from any breach by you of this Agreement. The Software is protected by federal copyright laws, international copyright treaties and other intellectual property laws and treaties. [. . . ]