User manual HITACHI L22D01UW

[. . . ] Instruction Manual 19"/22" HD Ready LCD TV with Built-in Digital Tuner and DVD Player L19D01 UB/UW/CB/CW L22D01 UB/UW/CB/CW GB Safety Warnings SOME DO'S AND DON'TS ON THE SAFE USE OF EQUIPMENT This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. ------------------------------------------------------------------------------------------------------------------------------DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between the pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and withdraw the mains plug before making or changing connections. [. . . ] ) Cab HDMI Cable (not supplied with the product) Troubleshooting Specifications 20 Using Conditional Access Module (CAM) The Conditional Acc ess Module (CAM) menu provides access to functions contained on the CAM. The module can be inserted into the Common Interface (CI) slot located at the backside (facing downwards) of the TV. A conditional access module (CAM) is an electronic device, usually incorporating a slot for a smart card, which equips a DVB television or set-top box with the appropriate hardware facility to view conditional access content that has been encrypted using a conditional access system. They are normally used with direct broadcast satellite services, although the UK digital terrestrial pay TV supplier Top Up TV also uses CAMs. Note This Conditional access module (CAM) does not come with the TV set. It can only be obtained when you subscribe to service providers like Pay TV or other service providers. Installing the LCD TV Specifications IMPORTANT Always switch the TV off before inserting or removing the module. Inserting the CAM 1. When using this type of module, first insert the viewing card into the module. Ensure that the arrow on the viewing card faces the arrow of the module before inserting into the module slot. Insert the module into the Common Interface (CI) slot on the TV at the rear panel. Press the / key to highlight "Setup" menu and press the OK key. / key to enter into the "Cl information" menu and press the OK key 8. Press / /OK key as indicated on the screen to access the CAM's functions. Using the DVD Features IMPORTANT If no module is inserted, the Conditioanl Access Module menu will display "Scrambled Program". If the module is not inserted properly, a warning message will show on the screen to remind the users. If you have inserted a module, please ensure it is fully inserted in the correct manner as mentioned in Step 2 above. The functions that now appear on screen are dependent on the contents of the selected Conditional Access Module in your country. Refer to the instruction supplied with the module or contact the vendor. Common interface Connectors at rear of TV(facing downward) ANTENNA HDMI 1 HDMI 2 Module (CAM) 21 Troubleshooting Using the TV Features Using the Features Introducing the LCD TV Preparation Preparation Introducing the LCD TV Installing the LCD TV Using the Features Using the TV Features Using the DVD Features Chapter 3 Using The Features BASIC OPERATION Tuning in the TV channels After connecting an aerial to your LCD TV and connecting the mains cable to the TV and 100-240V AC mains socket, turn the POWER SWITCH on (the | position) at the rear panel of the TV, and the red light will show on the front centre panel of the TV. Press the STANDBY button, and the red light will change to blue and the Installation screen will show: MENU Audio Setup Auto installation PN "0000" Country select Start Search OK ON FF LHD01 1. Make sure an aerial is fitted then press MENU button on the remote to start the "Auto Installation". After a few minutes, you will see the TV programs briefly as each channel is received and stored in the memory. To power off press the STANDBY button, the blue light will change back to red. Selecting a Source Press the INPUT button to display the function required ( TV/SCART/AV(YPbPr)/HDMI1/HDMI2/VGA ). buttons on the remote control or the buttons on the LCD TV to change the TV channels. You can directly select the TV channel required by pressing 1, 2, or 3 etc on the remote . Adjusting the Volume Press the VOL. +/- buttons on the remote control or the the volume. Troubleshooting Specifications / buttons on the LCD TV to adjust Note Adjust the volume level to its minimum first, and then slowly increase the volume to your desired level. 22 Using The Features To Mute the Sound Press MUTE and the sound cuts off. [. . . ] Press green key again to unskip the selected channel. LHD01 Press to select the channel, then press Red Key MENU screen. ANGLE TITLE Press and to set channel name. Then, press OK to confirm and store the channel name. LHD01 Tuned in all available channels. VCR TO INSERT A DISC Select DVD function before inserting the disc to the player. Play movies and other content on DVD, VCD, SVCD, and audio CD. 8 Using The Built In-DVD 9 1 2 3 4 5 6 DVD Functions Basic functions 1 After connecting the aerial to your LCD TV and connecting the mains cable to 2 A red LED indicator will show on the front panel of the TV. [. . . ]