User manual HITACHI HFC-VWS3D

[. . . ] NOTE · In this manual, unless any comments are accompanied, "the manuals" means all the documents provided with this product, and "the product" means this projector and all the accessories came with the projector. ENGLISH Contents First of all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Entries and graphical symbols explanation . . . . . . 2 Important safety instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Regulatory notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About Electro-Magnetic Interference . . . . . . . . . . . . . . . . 3 About Waste Electrical and Electronic Equipment . . . 4 Contents of package. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Loading batteries into the remote control . . . . . . . . . 5 Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · The projector has the DIRECT POWER ON function, which can make the projector automatically turn on. ( 17, 19) 9 ENGLISH Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector 14° horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 14 degrees. An elevator foot is adjustable while pushing the elevator button on the same side as it. Holding the projector, push the elevator buttons to loose the elevator feet. 1. After making sure that the elevator feet are locked, put the projector down gently. Hold the projector when twisting 1 5 To loose an elevator foot, push the elevator button on the same side as it. To finely adjust, twist the foot. CAUTION Do not handle the elevator buttons without holding the projector, since the projector may drop down. Do not tilt the projector other than elevating its front within 14 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself. 10 Displaying the picture your signal source. Activateon, and make it sendTurnsignal to source the VIDEO MY SOURCE/ COMPUTER DOC. CAMERA 2. To have the projector silent, press the MUTE button on the remote control. Loosen the screw (marked by arrow) of the lamp cover and then slide and lift the lamp cover to the side to remove it. Loosen the 3 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles. Insert the new lamp, and retighten firmly the 3 screws of the lamp that are loosened in the previous process to lock it in place. Lamp cover 3 3. While and thethe interlocking parts of the lamp cover projector together, slide the lamp cover back in place. Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu. (2) Point at the ADVANCED MENU in the menu using the / button, then press the button. (3) Point at the OPTION in the left column of the menu using the /button, then press the button. (4) Point at the LAMP TIME using the / button, then press the button. CAUTION Do not touch any inner space of the projector, while the lamp is taken out. NOTE · Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp. 13 7. ENGLISH Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. [. . . ] · Make sure the plus and minus terminals are correctly aligned when loading a battery. · Do not work on a battery; for example recharging or soldering. · Obey the local laws on disposing a battery. 16 CLOSE Using the CD manual The other manuals for this product are written into the included CD-ROM titled "User's Manual (detailed)". Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. [. . . ]