User manual HITACHI HDC-891E

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Select [Protect] with the / buttons from the playback menu, and press the SET button. Select [Single] or [All] with the / buttons, and press the SET button. Select [Cancel Protect] with the / buttons, and press the SET button. Formatting an SD/SDHC memory card or internal memory overrides protection, and erases all images regardless of their protected status. EN-23 DPOF Settings DPOF is the abbreviation for Digital Print Order Format, which allows you to embed printing information on your memory card. You can select the images to be printed and how many prints to make with the DPOF menu in the camera and insert the memory card to the card compatible printer. When the printer starts printing, it will read the embedded information on the memory card and print the specified images. Select [Single] or [All] with the / buttons, and press the SET button. Set the number of prints with the / buttons, and press the SET button. This creates a file containing the DPOF information, and when the operation is finished, the screen returns to the playback mode. The DPOF icon [ ] is displayed on each image that has set up DPOF settings. Play 1 100-0008 EN-24 Erasing Images Erasing single image / Erasing all images 1. Select [Single] or [All] with the / buttons, and press the SET button. To not erase, select [Cancel], and press the SET button. Deleting an image will not affect sequential image numbering. For example, if you delete image number 240, the next captured image will be numbered 241 even though 240 no longer exists. In other words, an image-number is removed when an image is deleted and will not be reused or reassigned to another subsequently captured image. EN-25 MENU OPTIONS Capture Menu This menu is for the basic settings to be used when capturing still images. 1. Select the desired option item with the / buttons, and press the SET button to enter its respective menu. Select the desired setting with the / buttons, and press the SET button. Scene Mode Refer to section in this manual titled "Setting the Scene Mode" for further details. * [8m] 8M (3264 x 2448 pixels) * [5m] 5M (2560 x 1920 pixels) * [3m] 3M (2048 x 1536 pixels) * [1. 3m] 1. 3M (1280 x 960 pixels) * [VGA] VGA (640 x 480 pixels) Quality This sets the quality (compression) at which the image is captured. *[ ] Fine *[ ] Standard *[ ] Economy Sharpness This sets the sharpness of the image that will be captured. * Hard / Normal / Soft Saturation This sets the saturation of the image that will be captured. EN-26 * High / Normal / Low White Balance This sets the white balance for a variety of lighting conditions and permits images to be captured that approach the conditions that are seen by the human eye. * [Blank] Auto *[ ] Day light *[ ] Cloudy *[ ] Tungsten *[ ] Fluoresc. When the sensitivity is raised (and the ISO figure is increased), photography will become possible even in dark locations, but the more pixelated (grainier) the image will appear. [. . . ] If the batteries or accumulators included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0. 0005% Mercury, or more than 0. 002% Cadmium or more than, 0. 004% Lead. Le marquage est en conformité avec la directive 2002/96/EC du DEEE (déchets d'équipements électriques et électroniques). Ce symbole indique l'obligation de ne pas déposer ce produit, y compris les batteries et accumulateurs vides ou déchargés, dans des décharges publiques, mais d'utiliser les systèmes spécifiques de retour et récupération disponibles. Si sur les piles ou accumulateurs inclus avec cet appareil, le symbole chimique Hg, Cd ou Pb est visible, cela signifie que la batterie a une teneur en métaux lourds de plus de 0. 0005% de mercure, ou plus de 0, 002% de cadmium, ou plus de 0, 004 % Plomb. [. . . ]